What is the best simulation for steel fiber in RC elements in ANSYS?

More Engmostafa Kalil's questions See All

How can we use differential pulse voltammetry to build a sensitivity curve. What are the best parameters should be selected?

I need also to understand the technique and know when it is useful. I used to run CV for qualitative analysis of my analyte and then do amperometry. Now, because I can not get a stair case from my...

20 July 2019 3,918 4 View

I want a simple definition for Willam-Warnke yield criterion for concrete failure ?

Is there any simple definition Willam-Warnke yield criterion for compression and tension that have been used in ANSYS as shown in attached fighure ?

30 September 2017 6,601 5 View

Any idea for how to start working with electrochemical quartz crystal microbalance (QCM), supporting materials or literatures?

I just bought the QCM cell from CH instrument and I do not know how to use it in parallel with Cyclic Voltammetry. I am using CV for metal-decorated graphene to enhance the electrode sensitivity...

02 July 2017 7,369 4 View

An early non convergence problem in modeling RC column in ansys?

I am trying to model Reinforced concrete column under Axial load only IN ANSYS.when i try to model RC column both ended are fixed with axial load i got non convergence problem at early time ,...

23 January 2017 5,231 4 View

How to exclude crushed element from stiffness matrix of ANSYS during solution?

Hello i am modeling reinforced concrete column under compression load in ANSYS, in early time of loading in solution the outer concrete cover elements crushed and i want to exclude the crushed or...

01 January 1970 2,321 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

In SEM, if a latent variable consists of three observed variables, and each observed variable has four items, what should I do?

Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...

31 July 2024 3,913 6 View

Belakhdar Khalil

Yes that’s right, but what is your question?

Marius Tarnovetchi

model the concrete with SOLID65, respectively the steel with BEAM188

Gildardo Galindo

usually concrete reinforced must be asig to SOLID 65 and steel bars to link 8 you must identify the version of ANSYS to clarify this theme..

greetings

Ahmed Mirghani

In addition to SOLID65 (Legacy Element), now Ansys Uses the Micro-plane model with CPT215 element and current technology elements SOLID18x. using Microplane you can model the gradual failure of concrete accurately and with out meshing sensitivity issues.