What is the best approach to make a hybrid nano fluid by dispersion of Cuo and Al2o3 nanoparticles in the water as a base fluid?

More Redhwan Almuzaiqer's questions See All

How do I see outputs of every layer of DNN OpenCV Python (visualization tool)?

I'd like to see the output of every layer of DNN under OpenCV Python. So, I am asking you here to help me. If anyone knows a blog or something else explain how to show us outputs of layers,...

25 May 2020 222 9 View

What is meant by object detection in real-time?

I read more paper and wrote for example: "real-time detection of people from the RGB-D image" or "robust detection and identification of a person in real-time (around 0.3 s)"

04 May 2020 4,581 1 View

Which SCI OR SCIE journal is fast for reviewing and the probability of acceptance is high in the robotics field?

human following robot using deep learning and depth image

08 June 2019 7,749 6 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Can chitosan alone can act as a reducing agent for Cu(0) nanoparticle sythesis?

[Synthesizing Cu nanoparticles without using chemical reductants]

01 March 2021 8,359 1 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

Isaac Lare Animasaun

The commonly employed equipments for dispersing nanoparticles in the basefluid are magnetic stirrers, ultrasonic bath, homogenizers, high-shear mixers, and bead mills.

Source:

Ali, N., Teixeira, J. A., & Addali, A. (2018). A Review on Nanofluids: Fabrication, Stability, and Thermophysical Properties. Journal of Nanomaterials, 2018, 1–33. doi:10.1155/2018/6978130

Gökberk Yalçın

Dear Almuzaiqer,

It is so obvious that using one step method plays very significant role to obtain better results. But it is not affordable method economically.

Best regards.

Abdelkader Mohamed Elsayed

Dear Redhwan Almuzaiqer,

This link maybe useful for you :

https://www.sciencedirect.com/science/article/pii/S1386947718300547