What is the affect of folding a PTFE Sheet repetitively? Would it cause the material to harden?

28 November 2017 1 998 Report

Multiple webpages (Including Wiki) state that FEP & PTFE do not withstand repetitive folding. Is the statement correct? and what would be the effect on the materials characteristics?

Peter Farrington

This paper has a very nice discussion of the mechanical properties of PTFE

https://doi.org/10.1016/j.polymertesting.2011.07.004

Mechanical behavior of polytetrafluoroethylene in tensile loading under different strain rates

L.C.S. Nunes, F.W.R. Dias, H.S. da Costa Mattos

Badges
Science topic

Similar topics
Correction

More Hussam Alnammary's questions See All

MATLAB ANN for Testing and Validating Interference?

Hello, I am trying to ANN from MATLAB to train ANN on effect of interference of one ion on another, and then based on this training providing 'accurate results'. I am new to Machine Learning...

23 June 2020 9,599 2 View

Upon your experience on site, how do you fix discolored concrete?

Upon your experience on site and concrete on site, the phenomena of discolored of concrete might happens... how do you fix that?

12 June 2020 4,857 46 View

Base on your academic experience.. whats the kind of question used in Online learning..?

For evaluation of students activity and for final exam... based on Online learning... what does the type question that must be adopted to makes the process work in the right way..

10 April 2020 6,112 56 View

Upon your site experience, did you estimate the life of the structure at designing process?

Life of the structure... is it real issue to be considered by the designers ... or its left to time to handled ..

10 April 2020 8,289 63 View

Is Monte carlo simulation suitable for structural application modeling?

Application of Monte-Carlo-Simulation in Structural Reliability, risk analysis or other complicated modeling.

22 March 2020 8,062 3 View

Upon your site experience, what must done, if the consultant reject part form the work carried out by the contractor?

05 April 2019 2,599 8 View

Upon your site experience, how can we repair the defect on beam due to steel corrosion?

05 April 2019 8,713 14 View

Upon your site experience, is it acceptable to make a join with ground beams?

05 April 2019 1,337 3 View

Extracting a fluid from a capillary tube?

I am planning to make a device where I utilize capillary tubes for extraction of sap solution from plants. My issue is trying to get the liquid out from the tube into a chamber where I have my...

13 March 2019 3,792 3 View

What is the main problems appear when concrete delay two hour during casting?

Upon your site experience, What is the main problems appear when concrete delay two hour during casting?

08 March 2019 9,699 3 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How to make a time series imputation benchmark ?

Hello ! In a work, I have to benchmark different algorithms to fill in missing values in time series. I insist on the fact that this is imputation and not forecasting. In my case, I have access...

24 February 2021 7,470 7 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View