Which theory is used to calculate shear stress in Ansys workbench?

Which theory is used to calculate shear stress in Ansys workbench? because I like to determine shear stress for a brittle material through Ansys.

31 December 2017 9,493 5 View

What forces should i consider to construct a Chassis?

I need to construct a 3D wooden bicycle trailer for Kids. The weight of bicycle trailers must also be light! I don't know where I should start? I thought I'd start from chasis, but what criteria...

11 December 2017 426 7 View

Sandwich made of low-cost materials that are environmentally friendly?

Are there current research results (maximum 10 years) that have successfully developed a sandwich made of low-cost materials that are environmentally friendly?I hardly find anything on the...

08 September 2017 4,007 7 View

Is there any other experimental method to determine the bending rigidity and shear stiffness of a sandwich?

is there any other experimental method to determine the bending rigidity and shear stiffness of a sandwich (three-point bending test) outside Allen's method?Allens method is described in his book...

08 September 2017 3,862 5 View

Why does ASTM C393 not contain a maximum deflection formula?

why does ASTM C393 not contain a maximum deflection formula?my samples are tested under standard ASTM C393Should I get the equation out of any other book?

08 September 2017 390 2 View

Any Paper about Base frame for supporting piston engine and drum Winch?

Hello, Any Paper about Base frame for supporting piston engine and drum Winch? Thank you

31 December 2015 7,039 3 View

Cellulose in water?

31 December 2015 8,574 6 View

Are there any papers about Pulp?

05 June 2015 2,446 7 View

How do I give more compressive strength in my sample?

Now I'm working on paper pulp, i'm creating a sample of the pulp. The paper in the ratio of 1: 7 in water. the ammonium bicarbonate was added to make the Porosity of my sample more large and i add...

05 June 2015 9,385 12 View

There any free software to connect it with my laptop and camera to follow the stress development during experiments?

01 January 1970 6,177 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View