What is Joule Thompson effect ?

17 May 2023 0 8K Report

I am not able to understand some basics. I require a detailed understanding and visual demonstration, as I am going to use it in my next research project.

Badges
Science method

Similar topics
Methodology

More Aayush Walawalkar's questions See All

How to correct background in Ce3d XPS data using CASAXPS software?

I have high-resolution XPS data of Ce3d (attached) in which Shirley background is crossing my actual data as shown in the figure. I need to correct it. Please find the attached '.txt' data file....

23 January 2020 2,535 6 View

What kind of properties are needed in ANSYS or other FEA packages to conduct the stress/strain analysis of 2D materials under tension, and bending?

I want to simulate the effect of stresses on a graphene monolayer and observe the deformations appearing in the material. The problem is the understanding of the element size and how to define a...

02 August 2019 9,005 4 View

Which type of filter membrane would be useful for pre-treatment of urine prior to ION CHROMATOGRAPHY analysis?

A standard protocol for pre-treatment of urine prior to analysis is required.

31 May 2019 7,386 3 View

What are some high level international conferences in which scientists have discussed about threats posed by microbes such as Candida, staph, etc ?

I am searching for some high level international scientific conferences in which world's top scientists have discussed about the serious diseases caused by the microbes found on our skin, head and...

04 February 2019 8,167 6 View

How to design a robust PID controller for a system with parametric uncertainties? How to implement it in MATLAB?

How can I design a robust PID controller for a second order plant having parametric uncertainties using h infinity. I tried using 'hinfsyn' function in matlab but it gives a higher order...

29 June 2018 942 5 View

How to keep size of the seed different for different regions in abaqus?

I want the width of the seed in the upper and lower sections to be different(more) than that of the seed in the middle region. I have specified different seed sizes for the edges in the middle and...

25 September 2016 2,444 11 View

What should be the plastic strain, when defining yield stress in Abaqus?

Isn"t the plastic strain zero at yield stress(atleast for non-brittle metals)?

03 September 2016 7,023 21 View

How can I dissolve graphene?

I want to dissolve graphene but I am not able to dissolve it. It got dispersed when I added 1M HCl solution to it.

25 October 2015 4,257 5 View

Any coefficients of heat capacity from a single source for thermodynamic study of phase transition(otherwise it is useless)?

I need the values heat capacity coefficients for C, H2, Mg, MgO, H2O, CO and CO2 from single source because these values change from 1 source to another source. I got one...

04 October 2015 612 7 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

How to visualize stress in a coating defined by "Skin" in Abaqus?

Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...

16 February 2021 1,594 3 View

How to perform Cox proportional hazard analysis or Kaplan-meier survival analysis in SPSS?

At first please see the attachment. This experiment was performed for a period of 7 days (n=100). After 7 days, we found different level of survival rate (%) for each treatment. Now, I want to...

15 February 2021 9,145 2 View

How to calculate visual angle of a visual stimulus?

I am currently trying to figure out how to calculate the visual angle of some visual stimuli I used in an experiment. I think I have all of the information I need to calculate this. One is a...

15 February 2021 3,189 2 View

Hyperspectral Image : open, visualize, process in Python?

I am looking for a tutorial or course to learn how to open, visualize , process hyperspectral images in .hdr , .raw format using python. Any recommendation for a tutorial is appreciated ? Thank...

08 February 2021 7,896 3 View

Recommendations for sample size in visual qualitative research (using children's drawings)?

Hi everyone! Asking for a little help, if I may. I am working on a research project, where I aim to analyse children's drawings about Covid-19. I am fairly new to using visual data in qualitative...

07 February 2021 9,530 3 View

How To Properly Show Displacement Versus Force For A Capacitive Parallel Plate With Multiple Electrodes in COMSOL?

I want to determine through simulation in COMSOL the displacements due to applied forces. The sensor has 4 bottom and 4 top electrodes that do not complete align along with a bump on top which...

21 January 2021 6,856 3 View

Inexpensive eye tracking hardware + software solution?

Hello, I am starting a project that will require an eye tracking device. I've seen eye tracking hardware + software solutions that are $10,000+ so I am hoping to find one that is significantly...

18 January 2021 8,121 12 View

Is it possible to combine two continuous variables into one categorical variable in order to create a dummy in SPSS ?

As background, in my model, my independent variable is visual clutter which has two conditions (higher visual clutter/ low visual clutter) and the conditions measure the amount of visual clutter...

13 January 2021 4,760 4 View