What is electro- chemical working station?

09 September 2014 0 4K Report

Can any one show me the main differences between "potentiostat" and "electro- chemical working station"

Badges
Science topic

Similar topics
Chemistry
Chemicals

More Amr Hessein's questions See All

How to calculate the absorption coefficient of a semiconductor numerically?

If I know the band gap if a certain semiconductor, and I would like to calculate the value of the absorption coefficient numerically using the following equation: how to determine the values of...

01 February 2017 3,517 1 View

Can anyone suggest a solar cell Modeling software for beginners?

I want to make modeling and simulation for thin film solar cell and thin film interfaces composed from nano structured materials. But I don't have any experience in that field. So any one can...

10 November 2016 2,447 43 View

What is the best method to fabricate Gold counter electrode for QDSSCs?

I had made many Au Counter electrodes using ion sputtering for different times. But the problem is these counter electrodes are not mechanically stable on the FTO substrate and peeled of with the...

02 March 2016 2,859 2 View

How to prevent the re-stacking of Graphene Oxide after reduction?

I want to get reduced graphene oxide powder, So, Is there is any method to prevent the re- stacking of graphene sheets after the reduction of graphene oxide?

02 March 2016 6,175 5 View

How to differentiate between allowed and forbidden transitions in direct band gap semiconductors?

Can any one tell me how to differentiate experimentallybetween direct allowed and direct forbidden transitions in direct band gap semiconductors. is there is a table or a database shows the...

01 February 2016 910 7 View

How to solve the counter electrode dissolving problem in quantum dot sensitized solar cell?

I made my counter electrode from nickel sulfide- Graphene composite on FTO substrate by using PVDF as a binder. But when the QDSSCs assembled by using polysulfide electrolyte, the counter...

09 October 2015 3,848 3 View

How do I solve the problem of continuous corrosion of metal sulfides counter electrode in the presence of polysulfide electrolyte?

my counter electrode for the quantum dot sensitized solar cell made from nickel sulfide. In the presence of polysulfide electrolyte, the counter electrode dissolving and contaminating the working...

09 October 2015 455 3 View

Did any one know the full spectrum of Ultra-high-performance lamp?

I want to use a Ultra-high-performance lamp as a light source in measuring the J-V curve of solar cell. But I want to know first the full spectrum of this lamp. does it emits in the UV range or...

04 May 2015 8,597 5 View

How to measure Solar cell J-V curve by Potentiostat?

I need to measure the J-V curve for solar cell using Princeton Versastat 4 potentiostat. How can I connect the terminals of the potentiostat?

03 April 2015 5,901 11 View

Why is in Raman is laser of wavelength 785 nm not compatible with graphene?

the most Raman spectrometers use LASER wavelengths of 533 and 633 during characterizing Graphene. When a LASER of wavelength 785 nm is used the D & G peaks in the spectrum are greatly shifted...

03 April 2015 2,628 9 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

What does an additional peak in FTIR between 3100 and 3300 nm affect the quality of the material, benzethonium chloride USP??

I do not know much about FTIR! The material Benzethonium Chloride USP was compared to a reference standard in regards to FTIR, as per the USP testing: Identification B. Infrared absorption (FTIR),...

16 July 2024 6,918 7 View

EIS spectra analysis software?

Dear all, I'm currently working with CHI potentiostat and performing Impedance. However, for the circuit fitting the instrument must be connected to the computer. Since I prefer to analyse the...

10 July 2024 8,880 4 View

Does the potentiostat have to be in a fume hood when polymerising the PANI?

I will polymerise Aniline on ITO glass WE, using 1M of H2SO4 and a potentiostat. However, I am not sure if I have to do the electrochemical polymerisation inside a hood. Is it necessary? Is the...

10 July 2024 2,937 3 View

What type of paraffin is recommended for preparing samples for cutting with a microtome?

Sample type: Corn leaves and stem Bean leaves and stem

22 June 2024 2,082 3 View

Declining peak in cyclic voltammetry analysis, what could be the problem and how can it be solved?

Hello everyone, As you can see from the graph, I initially observed a peak, but after the first scan, the peak started to diminish, and despite trying with a new solution, I couldn't achieve the...

10 May 2024 4,884 2 View

How to set parameter for galvanostatic charge–discharge (GCD) and Chronopotentiometry (CP) test in a work station (potentiostat) for supercapacitor?

Respected All, Recently I have been started working in supercapacitor. I am completely new in the field of supercapacitors. I have performed the CV. The weight of the active materials I used was...

03 May 2024 5,940 0 View

Can anyone please assist me in how to perform GITT both for batteries and supercapacitors?

We can have a pretty basic discussion about it. I am using Biologic SP-200 potentiostat.

24 April 2024 7,372 2 View

Why am I having CA overload at disk while doing a RRDE experiment?

I was trying to do RRDE experiment using Gamry. I appiled 1.2 V vs Ag/AgCl at the ring and 0 to -0.65 V vs Ag/AgCl at disk . The potential at disk keep stuk at around 1 V and does not go over the...

19 March 2024 2,230 0 View

How long does the stabilization of the OCP take?

The system is comprised of a nitrate solution (just nitrate ions in distilled water), and Screen-printed electrodes (Carbon working and counter electrodes, and Ag reference electrode). The three...

18 March 2024 9,467 1 View