In one of my sample, there are two peaks ranged from 10º ~ 12º, suggesting the new phase of ZIF-L. What is that phase - orthorhombic or cubic? Can anyone please provide JCPDS (ICDD) card number for ZIF-L?
ZIF-L is typically synthesized using 2-methylimidazolate (2-mIm) as the ligand.
The choice of 2-mIm and its interaction with zinc ions (Zn²⁺) is crucial in determining the final structure of the ZIF.
The coordination geometry of zinc ions with the 2-methylimidazolate ligands can influence the formation of a layered structure.
The type of solvent used in the synthesis process can affect the assembly of the framework. For ZIF-L, water is commonly used as the solvent.
The polarity and hydrogen-bonding capability of water play a role in guiding the formation of the layered structure.
https://doi.org/10.1038/s42004-021-00613-z
10.1039/C5TA03707G
We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...
01 March 2021 1,899 2 View
Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?
28 February 2021 3,653 4 View
Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...
25 February 2021 8,053 5 View
I used EdgeR to get the list of DEGs (differentially expressed genes) from my liver RNA-seq experiment. I have done the gene overrepresentation and GSEA based pathway analysis. I am currently...
23 February 2021 8,969 1 View
I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...
19 February 2021 2,787 1 View
Physiologically in cow, oestrous heat again goes on the peak after 2 months but locally this is not observed and AI is after two months but done after at least 6 months.
17 February 2021 685 4 View
I am trying to calculate the rdf of water molecules present inside the Carbon nanotube. I tried to do the indexing first using gromacs tool gmx selection. But when it comes to calculating rdf, I...
17 February 2021 1,066 3 View
The solar photovoltaic (PV) power plant uses commercial (non-concentrated) PV modules which are quite simple in design and reliable. They can work on fixed orientation and don't need the moving...
16 February 2021 3,796 9 View
I am working on a landslide model...i need an optical sensor to determine the amount of pore pressure and other values..i am thinking of using a microbend sensor. Can anyone please provide me with...
11 February 2021 5,911 2 View
Dear All, I am working on electric motor design in Ansys Maxwell. I have written optimization code in MATLAB. I want to run this code in ANSYS MAXWELL and generate FEA results. Does anyone know...
10 February 2021 1,279 1 View
The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...
03 March 2021 5,857 3 View
Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...
01 March 2021 3,867 3 View
I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...
01 March 2021 9,015 2 View
i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...
26 February 2021 2,499 1 View
I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...
26 February 2021 8,183 3 View
I have several Raman spectra with very distinct peaks at certain wavenumbers, such as 277, 359, 466, 583, 623, 686, and 795cm-1. How can I identify them to what compound(s)? The RRUFF and others...
24 February 2021 363 3 View
Hi all, I am doing a genescan analysis for a deleted exon in the patient sample. The amplified region is 215 bp. In the patient sample because of homozygous deletion, no peak is observed while in...
23 February 2021 5,645 1 View
I am refining my XRD data using in FullProf program. The intensity of the modulated X-ray peaks is almost flat. I tried to adjust the peak intensities but unsuccessful. What is the reason? I guess...
23 February 2021 2,304 4 View
We have deposited silicon carbide on carbon substrate using one PVD technique. Due to amorphous behavior of SiC at low deposition temperature, we performed heat treatment of those films at...
22 February 2021 2,072 3 View
I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.
21 February 2021 8,947 3 View