Using JEC 560 auto carbon coater
3KPa , and 30 s
I think its a bit too long.
Put a piece of paper in your coater, put a coin on paper. Coat, compare "whiteness" of coated not coated paper. Coated should be grayish, not dark, just grayish. Change time as needed.
i hope the technician will let me try it due to lack of resources
I dont understand how to prepare the solution because i dont understand what does it mean, and i dont know the conc. of the PSS stock solution.
31 December 2018 2,332 1 View
trying to analyze data at home while not in the lab
05 June 2018 8,424 0 View
Planning to do it this way, but cannot help worrying about possible changes that will happen to Co-Pi coating.
31 December 2017 5,262 2 View
Cross section cut of porous sample /FTO scratch off sample from the edge of the FTO making it hard to check in SEM. Need help to cut it so the film stays on the edge of the cut.
31 December 2017 9,786 0 View
Plan to make a paste but confused if we should wait for the sonicated powder to settle first and add binder to only the supernatant, or do we just add binder to the ultrasonicated powder...
07 August 2017 8,895 0 View
looking for a research paper synthesizing WO3 with the above ingredients.
05 June 2017 1,643 0 View
I added ammonium hydroxide and HCl to commercial WO3 NP in order to reprecipitating WO3 NP (chemical deagglomeration) but unsuccessful. The process results in large particles settles at the...
31 December 2016 6,081 6 View
some mass is loss in grinding before dispersion. solution is very dilute.
31 December 2016 7,462 2 View
its for thin film paste making.
31 December 2016 7,979 5 View
Faradaic process is the electron transfer across an interface in redox reaction, but i dont know how to determine how efficient this process is.
11 December 2016 2,823 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?
08 August 2024 8,915 0 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...
07 August 2024 5,343 2 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View