I am intend to raise a question about electrospun PVDF fiber, in presence of air if we burn this fiber what can we aspect to get at 700 to 800C?
Another I am not familiar with alpha form of PVDF which is piezo in nature, how to get this form?
thanks for answer Amin Shavandi
I would like to create a small guide containing the meanings of the names .. Thanks to everyone who cooperates with me in achieving it.
03 March 2021 5,266 4 View
I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...
03 March 2021 4,116 4 View
Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...
02 March 2021 1,999 5 View
Preference in terms of the scientific aspect
28 February 2021 796 2 View
I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...
27 February 2021 1,233 1 View
There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.
26 February 2021 5,851 1 View
I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...
26 February 2021 8,183 3 View
While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...
25 February 2021 4,591 5 View
i have frequencies of bridge that are effected by mass of vehicle. the problem is when any vehicle pass the bridge it would add the its mass to the bridge mass ultimately mass of the bridge will...
22 February 2021 10,004 3 View
For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...
21 February 2021 7,624 3 View
Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !
01 March 2021 2,501 3 View
In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...
26 February 2021 2,435 4 View
We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...
25 February 2021 568 1 View
I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...
23 February 2021 6,043 1 View
I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...
22 February 2021 4,290 1 View
does anyone know the best method to differentiate and quantify rapid fatiguing and fatigue resistant muscle fibers? the old method form the 1980's uses ATP staining which is quite labor intense?
21 February 2021 6,483 3 View
Hi guys, I am facing problems to interpret a DMA results. Material: Composite Bisphenol A + curaua fiber What is being tested: the influence of fiber volume on the composites properties...
12 February 2021 174 7 View
What is the reason of the received optical signal to be slimmed down in multi-mode fiber? I have 4 km multi-mode fiber
03 February 2021 1,105 10 View
I am modeling Carbon Fiber Reinforced polymer wrapped concrete column in Abaqus, but I have faced so many difficulties especially in the Model< Interaction and Constraint module. SO could you...
26 January 2021 6,795 4 View
Electrospining method is important for production of nanofiber .If doped with nanoparticles ,can be used for remove of contaminant such as VOC , but don't have mechanical strengh . For finding a...
24 January 2021 7,290 3 View