What happen if austenite finished temperature of Niti alloy's wire is lesser than body temperature (37 deg celcius) for wired stent applications?

30 April 2024 0 8K Report

Suppose austenite finish temperature of Niti alloy wire A is 25 deg Celsius and Niti wire B is 35 deg Celsius. Which one is best recommended for Biliary stent application and why?

Badges
Science topic

More Nishant Verma's questions See All

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

To perform transfection with DharmaFECT Duo in AGS cells. Could you tell me what the ideal concentration is to avoid significant cytotoxicity?

I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...

03 August 2024 3,851 1 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

What is Random Audit?

HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...

31 July 2024 5,309 7 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

How we can use lattice-based cryptography for construction of S boxes?

Please suggest basic literature on lattice-based cryptography. A kind response from the cryptographic community will be highly appreciated.

24 July 2024 6,291 4 View

I am working on III-V based tandem solar cells.Can anyone explain that solar cells work under forward or reverse biased conditions?

I want to know that n-doped side of solar cell is connected with positive or negative electrode.

20 July 2024 1,348 2 View

How much sample we are required to do a pilot study for standardized an Achievement Test?

I am conducting a study on Effectiveness of e-content on academic achievement of secondary school science student.

17 July 2024 5,633 4 View

Can it is possible to find the cleaved sequence when a protein cleaved by a heamaglutanin protease (HA/P) by any bioinformatics tools?

Bioinformatics tools like peptide cutter

15 July 2024 6,453 1 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

Please, what is the memory consumption of the Matlab function quad tree decomposition procedure [S = qtdecomp(I)] with respect to the input set I?

27 July 2024 5,455 2 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

How to maintain intestinal tissue resident cells (TRM) in culture?

I am attempting to culture tissue resident T cells (TRM) derived from fresh intestinal tissue for up to six days. I am finding that the viability of the T cells is low at D0, and a very small...

08 July 2024 4,887 2 View

Interested in Postdoc position in Mathematics at IMI-BAS BG?

Computational topology of solitons The well-established research area of algebraic topology currently goes interdisciplinary with computer science in many directions. The Topological Data Analysis...

08 July 2024 2,816 0 View