I'm trying a simulation of a bullet impact into polycarbonate plate of thickness 5 mm. For metals, the Johnson Cook parameters are readily available. But, I'd like to know where to get the same for modelling polycarbonate.
All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.
01 August 2024 589 4 View
I am an anatomist in Kurukshetra, Haryana India. we are trying to plastinate a fetus skeleton. we have done two acetone baths. can we go for impregnation or not
22 May 2024 7,140 2 View
looking for areas of research
20 April 2024 8,565 1 View
Examples of Forest cooperatives in Nepal
15 April 2024 1,670 0 View
Can it possible through trace element data to separate out the Zircon of Continent or crustal derived or from slab sediment input. I have bulk geochemistry data of rock.
04 April 2024 8,533 1 View
I want to check the mTORC activity and for that I am using rat kidney. I used cell lytic buffer from Sigma Aldrich to extract the proteins from rat kidney (50mg sample homogenized in 200ul cell...
27 February 2024 9,283 3 View
File is attached.
29 January 2024 7,733 4 View
I am working with a time series dataset using the `fable` package (R). I have fitted several models (e.g., ARIMA) and generated forecasts. The accuracy calculation is resulting in NaN values, and...
16 January 2024 7,660 2 View
why Lack of Fit P-values show star *
01 January 2024 330 3 View
Hello everyone, I am new in this topic and I am trying to reduce the reaction steps involved in oxidation of carbon in a fuel cell with the help of Ansys Chemkin pro (also any other possible ways...
24 December 2023 6,604 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...
31 July 2024 9,733 3 View