What elements can be doped in zinc oxide by using hot plate-magnetic stirrer and 1000 C furnace being available?

More b.c. Rai's questions See All

I have generated a figure "Gene distribution by conservation" from 20 genomes of bacteria. Can someone explain how to interpret correctly?

I have generated a figure "Gene distribution by conservation" from 20 genomes of bacteria. Can anybody explain how to interpret it correctly? Thank you in advance

11 January 2021 3,346 2 View

Which method is best applied to calculate the crack widths and check the crack control provisions in the super-long post-tensioned concrete slab?

For a super-long post-tensioned concrete slab, in which cracks are especially caused by restraint and predominantly formed by shortening due to shrinkage, creep, and elastic shortening of the slab...

19 November 2020 3,453 3 View

How to calculate thermal stress in cylinder if water is flowing inside the cylinder?

How to calculate thermal stress in stainless steel cylinder if water is flowing inside the cylinder?

14 October 2020 905 2 View

How extract and purify extracellular proteins expressed in E. coli?

Hello everyone, I am having trouble isolating and purifying an extracellular protein which I have expressed in E.coli. I have induced my protein at 0.5 mM IPTG by incubating it at 37 degrees for...

02 October 2020 8,223 3 View

How to apply initial strain/stress as prestress in SHELL63 element in ansys apdl?

hello all, I am using only shell63 element to represent slab in ansys apdl for simulating the Post-tensioned concrete slab structure. the main problem is how to apply initial strain/stress in the...

26 September 2020 6,454 3 View

How can we differentiate pre-tension and post-tension force in ANSYS APDL simulation?

Hello all, I am eager to know that how can we differentiate between the simulation of pre-tension and post-tension force in ANSYS APDL. In course of the simulation of a prestressed concrete slab,...

26 September 2020 6,520 2 View

Systematic Review and Meta-analysis?

Hi, I am planning to conduct a systematic review and meta-analysis since very long. However, found difficulty in literature search and statistical analysis. Please anyone advice me any easy way...

11 July 2020 7,868 13 View

Can I use the same research instrument for collecting data from two different populations?

Can I use the same questionnaire to collect data from health as well educational sector employees to measure their level of job satisfaction ?

02 July 2020 7,480 1 View

Can anyone help me finding good impact factor journals to submit uninvited review paper on postharvest chilling injury in fruits.?

I have tried submitting my review paper in relevant journals, but most of them only accept the review paper invited by the editor of the journal

28 June 2020 4,371 5 View

How to calculate the sample size for a clinical study where the exact disease prevalence is not available?

While planning clinical study like RCT on diseases like COVID-19, how can we calculate the sample size when exact disease prevalence is not available

01 May 2020 5,079 3 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to calculate Z (the number of molecules in a unit cell) for calculating theoretical density?

I am trying to calculate the theoretical density of my ceramics materials. I use the formula below to calculate the theoretical density: Theoretical density = (Molecular weight x No. of molecules...

24 February 2021 3,823 2 View

No streamlines present in a small region inside a flow. This means exactly what?

No streamlines present means whether the flow is getting obstructed there and the velocity inside the region is zero? Or else, the fluid is trapped inside that region with a nonzero velocity?...

22 February 2021 5,249 10 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

b.c. Rai

Sol-gel chemistry is possible.

F: sn oxide is possible.

Samar Layek

You can doped many transition metal (Fe, Cr, Co, Mn etc) in place of Zn in ZnO. There are many papers on this subject.

https://www.researchgate.net/publication/216446283_Effect_of_iron_doping_concentration_on_magnetic_properties_of_ZnO_nanoparticles?ev=prf_pub

Article Effect of iron doping concentration on magnetic properties o...

Shashi Rana

what may be future element for doping on ZnO nanoparticles

Thanks Samar bhai and Rana.I have a hotplate and want DMS of oxides of Zn and of Sn.

Samar Sir, If see the latest publication they have doped all the element (Fe, Cr, Co, Mn etc). My query was what will be future element for doping on ZnO?