It is a sponsored project to develop a gasket made up of FGM material and validate the nonlinear behavior of the FGM using Abaqus simulation. I was exploring the behavior of the gasket element type in my study.
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,991 0 View
The political participation of the Kirat Rai community in Nepal has evolved significantly over time: Historical Context Historically, the Kirat Rai people, like many indigenous groups in Nepal,...
05 August 2024 5,949 1 View
I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...
03 August 2024 6,069 3 View
I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...
03 August 2024 3,850 1 View
HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...
31 July 2024 5,309 7 View
I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...
31 July 2024 9,697 0 View
Genome-wide association study (GWAS) Continuous traits: eg. Height Discrete traits: eg. Eye color
28 July 2024 284 0 View
Please suggest basic literature on lattice-based cryptography. A kind response from the cryptographic community will be highly appreciated.
24 July 2024 6,290 4 View
I want to know that n-doped side of solar cell is connected with positive or negative electrode.
20 July 2024 1,347 2 View
I am doing a comparative study in which I will check the patient's progress by assessing their gait parameter, and to do that I will be using the abovementioned software. Still, before that, I...
17 July 2024 6,551 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,829 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,027 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 452 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,061 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,571 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 645 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View
I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...
16 July 2024 8,436 0 View
Aim is to simulate the shape of Mobius strip (an elastic ribbon) in simple way ( using Abaqus Learning edition). In literature, Mobius strip is modeled as Kirchhoff Rod / Cosserat plate. But, such...
15 July 2024 4,387 1 View