What could be the maximum pressure applied on the pure Copper for compaction?

Vignesh Babu R @Vignesh_Babu_R2

02 February 2018 0 10K Report

For consolidation purpose and what happens if if go beyond 500MPa pressure

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More Vignesh Babu R's questions See All

What is the exact usage of Epoxy/Copper based composites? where can I see the examples.?

general examples like packaging, sensors etcs., are known things. Exact point of usage

06 July 2018 1,167 0 View

How to find the sintering parameters using Thermo Mechanical Analyser(TMA) for copper?

rate of heating, sintering temp and holding time.

03 April 2015 2,317 2 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Addition of EDTA during the synthesis of copper nanoparticles to prevent it from being oxidized?

I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...

28 July 2024 8,027 3 View

How to do calculation of Louvain methods calculation for excel sheet and and is there any software available?

The Louvain method – named after the University of Louvain where Blondel et al. developed the algorithm – finds communities by optimizing modularity locally for every node’s neighborhood, then...

23 July 2024 6,659 0 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

Information is Stored by Context?

While living in Boston, which has a fine metro system, there were times that I would exit from underground at the wrong location, thereby expecting a particular visual scene only to be momentarily...

17 July 2024 3,237 10 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View

Pressure in Iron Iron Carbide?

What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?

05 July 2024 1,891 0 View

How to Perform Randall-Selitto Test (Paw Pressure Test) In Mice?

Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...

30 June 2024 6,004 0 View