What condition required for coating of Fe3O4@SiO2 by using APTES?

More Vijay Chavan's questions See All

Is this a facetotecta nauplius?

This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.

08 August 2024 3,746 4 View

How long will macrophages remain in the M1 state after treatment with 100 ng/mL of LPS?

In my experiment, I treated RAW macrophages with 100 ng/mL of LPS. After 24 hours, I collected the supernatant and replaced it with fresh media. I then quantified the cytokine levels of TNF and...

01 August 2024 476 2 View

What are the roles of both Monetry and Fiscal Policy coordination in optimising the Macroeconomic outcomes in the economy ?

These days policy coordination is becoming necesssary on different front. In India also it is the same case. Monetary and Fiscal policy interface is important in order to address the...

30 July 2024 2,104 6 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

When making abraxane with Nab tech, why is 9:1 Chloroform&EtOH used as solvents?

Is it the best optimization ratio based on experiments?

22 July 2024 8,170 0 View

Can diamond be grown using molecular beam epitaxy?

22 July 2024 9,755 2 View

How can I use LabVIEW to control of an ethernet-based driver?

Hello everyone, I am new to LabVIEW, right now we need to control the movement of an ethernet-based stage drive. We got the sample code from a collaborator but their instrument is USB-based, so we...

11 July 2024 5,385 2 View

Systematic review meta-analysis paper?

Hi everybody, We are trying to write a systematic review meta-analysis paper. But I could find 19 references. I think 19 references are not enough to do a meta-analysis section and it is better to...

10 July 2024 5,490 5 View

What psychological factors contribute to the prevalence of obesity?

Psychological factors contribute to the prevalence of obesity

08 July 2024 6,124 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

Why can't we get on top of this incubator infection (fungal)?

We have been experiencing repeated what looks very much like fungal contaminations in several incubators (in the same lab). We have tried the following repeated times and yet the coating on all...

02 July 2024 6,375 2 View

How to remove DDQ from bodipy reaction only possible colmun chomatography tecnique use here ?

bodipy moiety are high polar nature .so its are bottom of TLC PALTE up to 20;80(ethyl acetate;hexane) mixture so its binding in SiO2 SO YIELD is so decreased. how to remove DDQ from reaction mixture?

02 July 2024 8,846 4 View

Abdelkader BOUAZIZ Popular answer

Dear Vijay Chavan, the following documents deal with the preparation of Fe3O4/SiO2 core-shell nanoparticles. My Regards

https://doi.org/10.1021/cm302828d

https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7182715/

https://www.researchgate.net/publication/282040486_Synthesis_and_Applications_of_Fe3O4SiO2_Core-Shell_Materials

https://doi.org/10.1155/2020/4783612

Abdelkader BOUAZIZ

Vijay Chavan

Dear sir I, had already prepared Fe3O4@SiO2 core-shell nanoparticles, I want to coat Fe3O4@SiO2 core-shell with APTES (3-Aminopropyl triethoxysilane).

Doufnoune RACHIDA Rachida

Hi,

Please check the following documents.

With my best regards