If I enter my ongoing research, and if for any reason, I suffer a little delay, how will I be sure that some faster, more experienced researcher doesn't fly with my ideas and publish before I am done?
In that case do not reveal your idea here.
I assure you that I will not fly away if I am included in your any or all projects
Citation to your research my be delayed for about 24hr.
Increasingly, more articles are being retracted because of duplicate or otherwise dubious Western blots. Consequently, journals are asking for original Western blots and authentication of...
23 February 2021 8,609 3 View
Describe a serious ethical dilemma you have experienced. Use the 12 questions developed by Laura Nash to offer a solution to the problem.
21 February 2021 9,133 2 View
I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...
21 February 2021 2,882 1 View
I would like to quantify a recombinant protein (with native signal sequence) secreted by Pichia pastoris using the SDS PAGE. Since my standard protein (plant origin) is not pure, I would like to...
07 February 2021 3,880 9 View
Hi there, I am trying to measure dendritic spines from mouse fixed tissue, specifically, I am looking at the prefrontal cortex. I injected the PrL with a lentivirus to knock-down my protein of...
27 January 2021 9,251 2 View
So I am working with a drug that we know induces cell death in MDA-MB-231 cells. In other cell lines we have been able to identify that this drug induces ferroptosis. I have also done experiment's...
25 January 2021 3,587 3 View
Properties such as relative humidity (T 402sp-03), brightness and yellowness (T-452 om-02), whiteness (T-560 pm-96), opacity and absorption coefficient (T-425 om-01), tensile, breaking length and...
24 January 2021 308 3 View
I just installed PROCESS V3.5 in SPSS and am receiving the follow error when I try to run a model: ERROR: Variable names should be no more than eight characters in length. I don't recall...
11 January 2021 3,448 4 View
I am researching the application of iron oxide nanoparticle in the removal of heavy metal (Cr6) from soil
10 January 2021 3,167 3 View
I have searched all over the internet and I seem not to be arriving at its value. I need this value to perform some XRD measurements. Any help would be greatly appreciated.
05 January 2021 916 1 View
I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...
03 March 2021 8,920 3 View
How to upload pdf of my articles published?
03 March 2021 2,183 3 View
There are some books published in LAP. Shall I add it to the RG?
02 March 2021 2,753 1 View
I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...
01 March 2021 10,078 1 View
Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...
01 March 2021 9,911 3 View
it is published by Juniper
28 February 2021 354 4 View
Dear all I am going to publish my manuscript which is from my thesis in a good H-Index journal but I found them very expensive(I don't have financial support) based on the exchange currency of my...
28 February 2021 7,800 6 View
We have seen some authors use some software to write review paper. As obvious, the study of all published papers concerning our studying field is not possible and these software can help us to...
27 February 2021 6,296 1 View
I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?
27 February 2021 8,179 1 View
for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...
26 February 2021 3,668 1 View