Is this 6GHz wifi antenna create complexity at the time of febrication?

I have design a 6GHz antenna for wifi.The feed line width is 2mm and there are 2 parasitic elements beside this feed line with 1 mm gap.Is there any problem at the time of febrication?

04 February 2021 9,241 3 View

How can you make a PEDOT:PSS film using the doctor blade technique?

I have been trying to make an even PEDOT: PSS (PH1000) film with the doctor blade technique (tape casting) with varying results. I have been using a silicon substrate that's treated with piranha...

01 February 2021 8,506 5 View

How robust are open source soil moisture sensors connected to an arduino board for field monitoring?

Seeking recent experiences in the development and deployment of low-cost soil moisture sensors (ideally under $50/sensor) connected to arduino-based dataloggers. What is the longetivity of the...

19 January 2021 6,256 2 View

How to separate a mixture of organic acids by GC?

I would like to develop a method for analysis of many organic acids in the same time. how to separate the chromatographic peaks of each one?

20 December 2020 8,399 3 View

Should I keep the missing values > 50%?

I have a data set of 771 sample size. But some of the variables (laboratory findings like ALT, AST, creatinie level) have more than 50% missing values. Should I drop those? But I think those...

13 December 2020 4,847 3 View

How to Strip off HSQ( Fox 16) after etching?

We are finding a hard time to strip of residual HSQ ( Fox 16) after using it as a mask in etching? We are coating 600 nm thick HSQ and writing with 3000 microC/cm^2 dose at 1 nA current. We are...

08 December 2020 5,452 2 View

Why the oral cancer cell line from metastatic tongue origin is showing less aggressive property?

I am working with oral cancer cell line SCC090 (ATCC). As per ATCC data sheet it is originated from metastatic tongue. It's primary site is not mentioned. Due to the origination from metastatic...

08 December 2020 5,674 3 View

In case of larger sample size (more than 700 sample) can I do t-test though the data is not normally distributed?

My sample size is more than 750 but sk test is showing non-normal distribution. The variables have several outliers but I shouldn't remove those. In that case what should I do? t-test or other...

06 December 2020 1,285 19 View

Where to get free cancer patient demographic data?

Is there any freely available global repository to get cancer patients' demographic data? #cancer #cancer_research

06 December 2020 5,469 2 View

Why the western blot of HIF1alpha of the whole cell lysate shows intense band under normoxia without any induction of hypoxia?

I am working with oral cancer cell lines and trying to find the expressional changes of HIF1alpha under different experimental treatment. I am getting intense band of HIF1alpha in the western blot...

29 November 2020 5,707 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View

Onset of Photo Oxidation in Polymers?

Hi! I am looking for some specific information in regards to the minimum amount of UV intensity required to begin the photo degradation process in polymers. I understand each polymer is...

15 February 2021 7,703 4 View

Are there alternatives to the Devarda alloy when estimating nitrogen?

Are there alternatives to the Devarda alloy when estimating nitrogen? devarda alloy is reducing the nitrate to ammonium

15 February 2021 8,838 3 View

Passivation of chromium cast Iron in high temperature?

14 February 2021 2,157 3 View