How to calculate the CFU/ml for Mycobacterium tuberculosis growing in 7H9 broth?

I am running an experiment in which I need to calculate the CFU/ml of a Mycobacterium tuberculosis growing in 7H9 broth. Is there a reliable method to calculate cfu/ml for MTB since a culture of...

22 January 2021 10,027 2 View

IC50 value from this graph?

01 January 2021 6,848 4 View

What is the best Free/Open Source software for doing Taguchi and other design of experiments and associated meaningful analysis like ANOVA?

Also what are the different efficient DOE and Analysis methods w.r.to machining operation with a specially sintered tool?

03 August 2020 4,553 3 View

What is the current research scenario related to solid lubrication & solid lubricant based cutting tools?

What according to you should be researched/accessed with respect to WC based solid lubricant tools? What is your view with respect to future research in this area? (For e.g. Tribological study...

19 July 2020 3,232 6 View

Can I freely use figures from open access journals/articles by citing the article?

I am writing a review paper. In my paper, can I use figures from "open access" journals/articles etc provided I cite them properly? (i.e. without have to go for requesting permission for using)....

02 July 2020 9,363 15 View

How to import the irradiation flux profile from the ray tracing software TracePro to ANSYS Fluent as a boundary condition for thermal analysis?

I am using TracePro software for optical simulation of my solar concentrator system. The software gives the results as irradiation flux map and also the incident ray table. Now for thermal...

28 March 2020 5,216 4 View

How to interpret the XRD results to find the Chemical composition of the sample under study?

I have used EDX-SEM to identify the elements present in my powdered sample later I have used XRD got the results, now how to interpret the results to find the chemical compounds present in my...

31 October 2019 509 3 View

Is it possible to simulate the electrical output of a silicon PV cell using ANSYS ?

I am working on concentrated photovoltaic thermal system in which i need to simulate both its thermal and electrical output. Using ANSYS I am able to simulate the thermal output but how to do a...

31 October 2019 7,673 2 View

Under what circumstances can we consider mass equivalent to weight and vice versa ?

Can mass be always considered equivalent to weight ?

17 September 2019 7,790 3 View

How to do mechanism study in photo-catalytic degradation of pollutant?

Dear Friends, I am currently doing some experiment where i prepared some nanomaterial and now trying to degrade dye molecule under visible and UV light condition. I need help regarding setting up...

21 May 2019 1,567 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

What are the most reliable approaches to extract key continuous frames from a video, with complete automation?

I have an input video, of skin (from a microscope that means it is magnified such that blood capillaries are visible). The idea is to extract 15 sec of continuous frames from a video of 1 min,...

02 March 2021 2,735 2 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

Which is the best place in the world for the plant biotechnology research?

I am searching for a good place for the Post Doc,

02 March 2021 4,053 3 View

How can extract ciprofloxacin hydrochloride disolve in water er to organic solvent such as dichloromethan or any other solvent?

I need a procedure to extract the ciprofloxacin hydrochloride from aqueous solution by using dichloromethane in detail,. I thank you very much.

01 March 2021 4,306 1 View

Which bacteria are suitable for quorum sensing screening?

I want to find a quorum sensing inhibitor from plant extracts. Klebsiella pneumoniae, Moraxella catarrhalis, Staphylococcus aureus, and Streptococcus pneumoniae. I looked for these strains...

01 March 2021 7,675 3 View

Isolates of Hymenoscyphus fraxineus?

Dear Dr. Cai, my name is Simone Prospero and I work in the team of Phytopathology at the Swiss Federal Institute for Forest Snow and Landscape Research (WSL;...

01 March 2021 1,133 1 View

How to perform statistical analysis of coefficients extracted from transform techniques?

I am studying the potential of DCT and FFT coefficients extracted from a signal to classify the different objects that emit the signal. I applied the Shapiro-Wilk to confirm that data was not...

01 March 2021 8,079 2 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View