What are the reliable low cost sensors that can be used to measure ambient CO, NOx, SO2, NMHC, CH4, O3 ?

D G G P Karunaratne @D-G-G-P-Karunaratne

09 July 2014 0 297 Report

The intention is to set up a low cost AQ monitoring network for modelling and validating ambient AQ in a given area.

Badges
Science topic

More D G G P Karunaratne's questions See All

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

While doing Chronoamperometry, when the light is turned off, why the current is not decreasing sharply?

Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.

29 July 2024 4,538 3 View

Is it possible to dock more than one drug in the same active site or pocket of a protein to study synergistic/antagonistic/additive properties?

I wanted to know whether we can observe the synergistic/antagonistic/additive properties of combinations or mixtures of compounds through docking analysis. But during docking preparation any...

28 July 2024 7,413 6 View

How to interpret results of AST for Pseudomonas aeruginosa?

While doing AST for Pseudomonas aeruginosa, after incubation, no zone of inhibition observed in the plate near the well. wells surrounded by bacterial growth, when the same plate observed under UV...

25 July 2024 9,229 1 View

What is the Principle of Cysteine-carbazole-sulfuric acid reaction with glucose?

I have been looking for the principle of Cysteine-carbazole-sulfuric acid reaction in research papers and books, but couldn't find it. This reaction is mainly used for the quantification of...

23 July 2024 3,891 0 View

How can AI technology to enhance the agricultural productivity?

Farmers no longer have to apply water, fertilizers, and pesticides uniformly across entire fields. Instead, they can use the minimum quantities required and target very specific areas, or even...

22 July 2024 8,296 3 View

Can a paper that is posted as a preprint in a database with DOI, can be reviewed in another journal and accepted for publication??

It happened that I am asked to review a paper for a journal. Incidentally, the paper is posted as a preprint in another database as open access with DOI. It is completely citable. Now, should I...

17 July 2024 1,831 4 View

Do software tools exist to assess the economic and technical practicality of introducing new food products, such as yogurt with modified starch?

This question explores the world of food innovation and asks if there are computer programs that can analyze the financial and technical feasibility of introducing new food products. For instance,...

13 July 2024 7,446 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,600 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View