What are the preliminary ways to check if a (thin film) diode is working?

11 November 2017 0 3K Report

I tried fabricating a thin film diode, from solution process.I understand that the IV characteristics confirms the diode behaviour, but is there any other (preliminary) way to check if the diode will work or not?

Badges
Science topic

More Devika Mahesh's questions See All

Can the sudden change of transmittance at the critical wavelength be influenced by the crystallinity of the material?

From the Transmittance spectra of my TCO samples, I found that the the slope is not same for all the samples. Can the steepness/slope of the transmittance spectra be linked to the crystallinity...

05 June 2018 5,038 0 View

How does energy band gap depend on crystallite size(from XRD)?

Will the crystallites directly influence the band gap? How?

04 May 2018 2,196 0 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Mediation path analysis - Can I run two seperate models?

I am wanting to run a serial mediation model with 2 x IVs, 2 x MVs, and 3 DPs (all continuous). Is it problematic to run 2 different models for each IV, keeping the MVs and DPs the same in each...

27 February 2021 5,681 3 View

SEM or Multiple Regression for an analysis without Latent Variables?

Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...

26 February 2021 8,399 5 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View