Can a published paper be published as a chapter in a book?

This question is about whether the published paper can be published as a chapter in a book.

02 January 2021 5,156 4 View

Nano Ice films sublimate due to low dose beam and annealing under vacuum? which one is more likely dominant?

An ice film sublimates under a severe vacuum pressure and a low does of electron beam. when the sample is in-situ annealed the sublimation rate significantly induced. In an isobaric process,...

06 November 2020 7,576 2 View

To simulate handover in wireless ad hoc networks, what are the freely available academic network simulation tools?

I wanted to simulate a handover algorithm for ad hoc networks, I want to know what are freely available supporting tools for academic research?

28 September 2020 4,604 7 View

What is the chemical name of Zn(0.3) Mg(0.7) Cr(x) Fe(2-x) O(4)?

Is this ferrite is from the spinel group? can anyone explain the tetrahedral and octahedral sites pf elements for this above formula? If Cr(2+) and if Cr(3+) is doped, describe the...

08 September 2020 4,472 2 View

PV Microgrid island mode modelling using Homer pro, battery sizing method?

For lower size PV installed capacity, Battery size 2-3 times of the higher size. For a installed capacity 70kW PV system, the battery size =300 kWh battery For a installed capacity 300kW PV...

08 September 2020 2,827 1 View

What is the most efficient way to make quad meshes in 3D in ANSYS Fluent?

I am planning to run ANSYS Fluent simulations in 3D. While I have a lot of experience in meshing in 2D, I have no idea on how to form 3D meshes in ANSYS Fluent. The geometry I am working with has...

25 August 2020 7,902 3 View

Can anyone suggest a good textbook / article on shock / boundary layer interactions?

I am currently working on a project involving shock / boundary layer interactions using experiments and CFD. I am looking for some books / papers where I can get the theoretical understanding of...

11 August 2020 2,748 3 View

What is the best method for encapsulation of lactic acid bacteria in proteins?

What is the best method for encapsulation of lactic acid bacteria in proteins in acidic conditions?

09 August 2020 9,633 9 View

Can we use Ethanol Amine or Poly ethylene glycol instead of Oleic Acid to synthesize Molybdenum Disulfide (nano)? Either Yes or No, What is Reason?

I want to Synthesize Molybdenum Disulfide at Nano Scale. Can I use Ethanol Amine or Poly ethylene glycol instead of Oleic Acid? Please brief with the reason.

26 July 2020 913 3 View

Can anyone suggest a good textbook on finite element methods (FEM) and its programming in MATLAB?

I'm planning to learn the basics of FEM and also want to be able to solve all kinds of problems numerically using MATLAB. I'm looking for some textbooks and/or sources where I can learn about...

24 July 2020 3,911 12 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View