Which microtomy technique do you suggest for thin and delicate root sectioning ?And, how to preserve and process the roots before sectioning?

We have thin roots of from 1 year old different species of plants. We are looking into anatomical details of the roots. What's the best method to preserve and process the roots once they are...

23 February 2021 1,898 1 View

Has anyone done Archard Wear Simulation of GFRP Composite Plate in ANSYS with ACT extension or UDF?

I'm looking to do a sliding wear (plate-on-plate) simulation of GFRP composite plates with Archard Wear Model. Any hints or example steps are appreciated.

17 February 2021 1,447 2 View

Which root in this tap root system, in the picture attached, should be used for root sectioning in order to study the root anatomical details?

There are numerous roots in this tap root system. Kindly suggest or share a research paper where I can clarify the doubts as to which root should be chosen for sectioning and for further root...

14 February 2021 1,816 3 View

Possible problem for showing 0.2 sun intensity instead of 1 sun intensity in AAA class Newport solar simulator?

We have a AAA class Newport solar simulator. We changed the Xenon Arc Lamp recently (XBO450W, Make:OSRAM) as the lifetime got over. However, the intensity is coming to be only 0.2 sun instead of 1...

14 February 2021 9,998 3 View

How can I get access of UNAfold tool?

I am searching for tools to construct molecular beacons which shall be complementary to a given sequence. I don't want to design any primers. I found that UNAfold is one such tool which I could...

02 February 2021 9,065 5 View

The peptide synthesized with CTC resin have mass more (+68 Da) than the desired mass of the synthesized peptide. What could be the reason?

I am synthesizing 7 amino acid long peptide sequence with CTC resin, 50oC coupling for 10 min. On cleavage (TFA/TIPS/Water 95:2.5:2.5) I got peptide with good yield. However, It has 68 Da more...

30 January 2021 8,483 3 View

How do we calculate curvature value in ArcGIS?

Hello everyone, I am trying to prepare curvature map in ArcGIS 10.4, using spatial analyst tool. I am using 10 m CartoDem (projected in UTM 44N). I am getting very different value, curvature...

12 January 2021 504 4 View

How can a publish my case report?

I want to publish a case report regarding jejunal diverticula

02 January 2021 7,630 5 View

How can we maintain the two different DC high voltages of same polarity between parallel electrodes inside the vacuum separated by few millimeter?

I am trying to maintain two different high DC voltages of same polarity (either positive or negative) between two parallel electrodes separated by 500 um inside the vacuum. However, what I found...

21 December 2020 1,735 3 View

Is it any standard method to preparation of active layer materials (blend donor & acceptor ) for organic bulk heterojunction solar cell ?

Hello friends , when I prepare blend donor and acceptor for active layer of organic solar cell I am take donor and acceptor in 1:1 ratio and concentration variation between 10mg/ml to 16mg/ml. I...

16 December 2020 3,876 4 View

How can extract ciprofloxacin hydrochloride disolve in water er to organic solvent such as dichloromethan or any other solvent?

I need a procedure to extract the ciprofloxacin hydrochloride from aqueous solution by using dichloromethane in detail,. I thank you very much.

01 March 2021 4,306 1 View

Which bacteria are suitable for quorum sensing screening?

I want to find a quorum sensing inhibitor from plant extracts. Klebsiella pneumoniae, Moraxella catarrhalis, Staphylococcus aureus, and Streptococcus pneumoniae. I looked for these strains...

01 March 2021 7,675 3 View

How to perform statistical analysis of coefficients extracted from transform techniques?

I am studying the potential of DCT and FFT coefficients extracted from a signal to classify the different objects that emit the signal. I applied the Shapiro-Wilk to confirm that data was not...

01 March 2021 8,079 2 View

How to remove fatty material from plant extract?

The resultant solid was partitioned three times with 250 ml of petroleum ether (40-60/c) to remove any fatty material and evaporated to dryness.

28 February 2021 9,464 2 View

Can water be extracted from Olivine?

I have always been interested in geology and wondered about how unique structures of materials behave in different circumstances. I stumbled upon Olivine, the magnesium iron silicate, and heard...

28 February 2021 7,330 4 View

How to make fractions of chloroform extract of plant, using seperating funnel?

28 February 2021 8,466 2 View

Good morning research fellows, Has anyone worked with senna alata plant extract on any kind of fish?

Literatures on the piscicidal effect of sennaa alata is scanty. if you have any related litrature either in the bark, leaves or roots used as treatment to any aquatic organism please kindly help...

28 February 2021 9,138 2 View

How to arrange coordinates and extract climate dataset out of MPI-ESM-MR netcdf files?

Have a nice day everyone, I'm stuck in extracting datasets out of MPI-ESM-MR netcdf files because the latitude ranges from -3*10^6 to 3*10^6 and longitude ranges -5,9*10^6 to 5,9*10^6. Plus, the...

28 February 2021 912 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

What is the most suitable resuspension buffer for TCA/acetone precipitated protein?

I need to extract protein from fermented carbon sources for Bradford assay. Most researchers experiencing insolubility of pellet in resuspension buffer. Please assist me to select most suitable...

26 February 2021 7,129 3 View