The breakthroughs expected in the next decade, especially in the areas of fluid dynamics and hydrodynamics.
I think understanding in tribology at nano and atomic scale will increase in coming decade. This i think will be the thrust area in coming years.
Tribology has many applications in mechanical systems, especially for machinery components and parts. However, there is a wide range of applications in other areas that are also very important and...
07 August 2017 7,921 7 View
I'm looking for papers presenting theoretical and experimental studies of the tribological properties of graphene, especially those related to improving lubricants under boundary lubrication and...
02 March 2015 7,621 5 View
Considering both scuffing, generally speaking, and scuffing on piston rings, for example.
11 December 2014 443 15 View
How can the feeding flow influence on its performance, when it's smaller or bigger than the numerically predicted axial fluid flow?
07 August 2014 5,954 2 View
Suggestions on any recent publication discussing the use of Reynolds equation for fluid-film lubrication or for hydrodynamic bearings, or presenting any new approach. Thanks in advance!
04 May 2014 8,325 3 View
Is there any relation between this limit and the accuracy of the numerical prediction of fluid-film bearing dynamic coefficients?
11 December 2013 7,437 11 View
Where can I find a reliable source providing stiffness and damping coefficients for fluid-film bearings, especially elliptical and non-short bearings?
10 November 2013 3,923 7 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...
03 August 2024 3,371 3 View