What are the limitations of using diode laser for pumping some lasers?
Thank you so much for you attention and response@AL Timimi Zahra
Turghun Matniyaz Thank you very much for your answer and effort
Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...
03 March 2021 6,317 1 View
I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?
25 February 2021 7,187 3 View
I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...
21 February 2021 7,128 3 View
Please suggest ways to learn Fuzzy VIKOR methodology in a best possible way. And is there any toolkit available for the same? Thank you in advance.
20 February 2021 8,271 3 View
I am trying to simulate the impact of a sinusoidal force on a Beam, yet I registred this beating signal (Displacement by time). The freaquency of excitation was the same as the first natural...
19 February 2021 5,872 3 View
Hello all, I want to simulate a Dielectric Elastomer Actuator DAE (an electrostatic-Structural analysis). I want to apply various voltages and frequencies into the DEA in the form of sine wave....
13 February 2021 3,261 3 View
Dear I have an air reservoir with 50 bar pressure , this reservoir is fed by 2 bar air pressure source, I would like to instal air pump ( 30 m3/h ) to evacuate the 2 bar fed pressure so I always...
06 February 2021 3,520 3 View
Hello everybody My research involves an intervention where an instructor delivers a training course to students. My role as a researcher is to write down observations. Do you have any idea about...
03 February 2021 6,853 3 View
my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?
01 February 2021 7,140 4 View
I was wondering: in common DFT (or Hartree-Fock) algorithms/codes, and in particular in solving the Roothan equation, what is the most computationally expensive part: 1- evaluate all the terms of...
01 February 2021 396 2 View
In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?
01 March 2021 1,923 3 View
I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...
28 February 2021 4,890 3 View
25 February 2021 1,987 3 View
It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...
24 February 2021 5,974 4 View
Does the absorption coefficient of the semiconductor changes with the change in the structure of the semiconductor? If you have a thin film and nanowire of the same semiconductor, will the...
23 February 2021 9,799 4 View
I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...
17 February 2021 8,104 4 View
I used laser capture microdissection, selected specific bacteria presented in ethanol-fixed slides. And DNA was extracted by Qiamp mini kit. The problem right now is we have pretty low...
09 February 2021 3,908 2 View
Dear sir, How to measure cosine, abbe, deadpath errors. I know cosine error, abbe error, deadpath error occurs in laser measurement. But how i can identify the cosine error value. Is any separate...
03 February 2021 4,878 4 View
Dear Fellows, now it is the time to push graphene applications further in terms of easy and low cost production surroundings. Thus I recently dived in the materia and I am facing tons of papers,...
02 February 2021 6,284 2 View
Which of the methods like water jet cutting, diamond cutting, laser cutting, etc. is more suitable to cut the carbon nanotubes reinforced epoxy composites into test sample to ensure the clean...
29 January 2021 1,354 5 View