How do I rectify NDVI values ranging from 0 to 0 after using reliability data to flag out bad pixels?

I am performing NDVI anomaly analysis in ArcMap using MOD13Q1. After flagging out the contaminated pixels some data sets have NDVI values ranging from 0 to 0. How do I correct this?

27 August 2020 1,387 1 View

How can i make a scatter graph showing both steps and line connectors?

As part of my research study, I have been trying to make my result representation for measured and predicted values for Cesium-137 depth distribution pattern. However, i find it difficult to plot...

11 December 2019 4,216 2 View

What is the gap between bench-scale reactors and commercial or industrial scale reactors?

In scaling-up laboratory technologies, what are some of the areas to consider throughout the demonstration stages in order to get the technology to the commercial application?

08 September 2019 9,818 1 View

What are some of the ways to measure attitude of stakeholders in conservation?

how to measure government official, NGOs tourist.

11 December 2018 4,333 0 View

What are the things researchers look out for in analyzing lab data?

Dear Researchers, Please share the details you look out for when analyzing data/ or raw results from experiments (both qualitative and quantitative). How do you make your discussion sections look...

10 November 2018 816 6 View

How do I find the significance level of 2 defined multiple responses in SPSS?

Want to run a cross tab for 2 categories of multiple responses. First category is Times of the day i.e Dawn to Midnight and the second category is Destinations (School, Work, Home, etc). But I...

07 June 2018 6,887 2 View

Storage of DNA from excised gel

please how best can DNA from excised gel be stored for 2 weeks? thank you

18 July 2017 2,580 3 View

How can I prepare 10mM Tris-HCl (pH = 7.5)?

I want to use this to run RAPD in the lab

10 November 2016 1,497 3 View

Which micro enterprises use postponement as a strategy in their businesses?

10 November 2016 1,343 0 View

What are the hottest research areas (issues) in Security in WSNs?

Hi everyone. I want to know the current research issues (areas) in Security in WSNs. I am specifically looking at DOS attack at the various layers of WSNs or Intrution Detection in WSNs. All...

20 October 2016 9,305 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View