What are the advantages of TiO2 coating over SiO coating on copper substrate for pool boiling heat transfer?

10 October 2018 0 9K Report

Badges
Science topic

More Mukul Ray's questions See All

Why nano fertiliser will be used in Agri-sectors? Will nano fertilisers impove the quality of Agri-products? if YES/NO why?

Before to start work with nano fertilisers, it is important to know the advantages/disadvantages of nano fertilisers for application in Agri-sectors.

09 October 2018 2,538 1 View

Which procedure can be followed in contribution of authors (individually) of a research paper obtained from experimental work?

Research scholar, Co-Guide & Guide perform an experimental work & then they prepare a research paper. As it is a team work, a procedure should be followed to measure for author's...

09 October 2018 1,978 0 View

Please, do you have an idea, why DOI is essential for a research articles or papers ?

What is DOI & why ?

09 October 2018 9,874 0 View

I want to ask, INDIUM nanoparticles are safe to use for pool boiling experimental work with refrigerant R-134a & R-141b?

I want to continue my research work with Indium nanoparticles. So, it is important to know how much it safe nanoparticles?

09 October 2018 7,335 0 View

What are the procedures to measure the thickness of thin film?

09 October 2018 6,414 0 View

Please, do you have an idea how can we prepare TiO2 nano layer with SOL GEL method?

We want to work for enhanced pool boiling heat transfer of refrigerants on TiO2 nano coated surface, fabricated by sol gel technique. So, it is essential to prepare TiO2 nanocoated surface over...

09 October 2018 727 0 View

What are the physical & chemical properties of In2O3 ? What are the advantage & disadvantage of using In2O3 ?

I am interested to work with In2O3 nanoparticles for surface coating. It is necessary to know it's behavior.

08 September 2018 3,710 0 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What are the perfect mathematical model for a solar-powered ship implementation?

A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids

28 July 2024 4,985 1 View