Please, do you have an idea how can we prepare TiO2 nano layer with SOL GEL method?

10 October 2018 0 727 Report

We want to work for enhanced pool boiling heat transfer of refrigerants on TiO2 nano coated surface, fabricated by sol gel technique. So, it is essential to prepare TiO2 nanocoated surface over copper bare surface Sol Gel.

Badges
Science topic

Similar topics
Chemistry
Nanotechnology
Nano

More Mukul Ray's questions See All

Why nano fertiliser will be used in Agri-sectors? Will nano fertilisers impove the quality of Agri-products? if YES/NO why?

Before to start work with nano fertilisers, it is important to know the advantages/disadvantages of nano fertilisers for application in Agri-sectors.

09 October 2018 2,538 1 View

Which procedure can be followed in contribution of authors (individually) of a research paper obtained from experimental work?

Research scholar, Co-Guide & Guide perform an experimental work & then they prepare a research paper. As it is a team work, a procedure should be followed to measure for author's...

09 October 2018 1,978 0 View

Please, do you have an idea, why DOI is essential for a research articles or papers ?

What is DOI & why ?

09 October 2018 9,874 0 View

I want to ask, INDIUM nanoparticles are safe to use for pool boiling experimental work with refrigerant R-134a & R-141b?

I want to continue my research work with Indium nanoparticles. So, it is important to know how much it safe nanoparticles?

09 October 2018 7,335 0 View

What are the procedures to measure the thickness of thin film?

09 October 2018 6,414 0 View

What are the advantages of TiO2 coating over SiO coating on copper substrate for pool boiling heat transfer?

09 October 2018 8,779 0 View

What are the physical & chemical properties of In2O3 ? What are the advantage & disadvantage of using In2O3 ?

I am interested to work with In2O3 nanoparticles for surface coating. It is necessary to know it's behavior.

08 September 2018 3,710 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Why is my ASO degraded quickly on agarose gel?

I have been working on Red blood cell-derived extracellular vesicles as Antisense Oligonucleotide (ASO) carriers. We normally run agarose gel to quantify the loading efficiency. I used naked ASO...

06 August 2024 3,130 2 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

Nano Orange protein quant on the Quantus fluorometer?

Is anyone here using the Thermo Fisher Nano Orange kit for protein quantification, and detecting the fluorescent signal on the Promega Quantus? We are struggling to make sense of the standard...

05 August 2024 8,946 3 View

What are possible strategies can be used to analyze data under sequential explanatory mixed method approach?

Better ways to analyze the qualitative and quantitative data in a sequential explanatory mixed method approaches

04 August 2024 2,703 6 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

I'm optimizing a tetra-ARMS PCR protocol with amplicon sizes: 165bp, 123bp and 93bp. Why, in the gel, only 165bp is visible while I'm expecting all 3?

It's an end-point PCR protocol. I'm using 1.5% agarose gel with SyBR Safe dye and TBE as a running buffer, visualization on BioRad XR+ system. I was primarily thinking of primer efficiency,...

01 August 2024 4,673 4 View

Why 3 replicates for most biological assays? Is it enough to examine the data fits normal distribution?

Just bounced on me. Before statistically analysing significant difference, shouldn't we see if data fits normal distribution first? Is 3 replicates enough to testify the hypothesis of normal...

31 July 2024 8,141 13 View