What are CCT, TTT and phase transition diagrams of different steels in welding process?

Amirreza Rouhani Esfahani @Amirreza_Rouhani_Esfahani

05 May 2018 0 5K Report

Every welding procedure is dealing with heating and cooling the different materials. Is there any reference for CCT, TTT and phase transformation diagrams of different steels?

Badges
Science topic

More Amirreza Rouhani Esfahani's questions See All

What are the different methods and chemical reactions of Au reduction from HAuCl4?

I am working on the reduction of Au nanoparticles from HAuCl4 for preparing Au NPs and I am looking for different methods of reduction and chemical reactions of this reduction.

04 May 2019 9,804 1 View

What are the conferences and symposiums in the field of nanomaterials, advanced materials or microfluidics?

What are the most important conferences and symposiums in the field of nanomaterials, advanced materials or microfluidics in the Canada and USA?

04 May 2019 5,495 11 View

Is there any colorimetric reactions for the detection of phosphate in water?

I am looking for a nanomaterial which is sensitive to phosphate and I can use it as a sensor for phosphorous detection.

01 February 2019 6,972 3 View

What is the best coating material for absorbing short wavelength radiation (i.e. X rays) and transmit the long wavelength(i.e. light)?

I have a devise which i want to coat since i want to absorb radiations with high energy like X Ray and transmit low energy rays like light. what would be the best material for coating?

31 December 2017 9,927 1 View

How to find lattice constant with calculation of lattice strain?

I have XRD patterns from some different samples of Cobalt ferrite and i want to compare these samples lattice constant with calculating lattice strain and that's because if lattice strain be...

04 May 2017 8,830 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Why is trifluoroacetic acid (TFA) used in c-18 column?

I would like to know the role of the TFA (trifluoroacetic acid) used on reverse phase chromatography c-18 column. It's is often used with a concentration of 0.1% on the mobile phase.

23 July 2024 8,075 3 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View