Way(s) of making a P(VDF-TrFE) monolayer for Langmuir-Blodgett film coating?

24 August 2022 0 6K Report

I am looking for a way of assembling P(VDF-TrFE) monolayer on the liquid/air interface so that it can later be used for coating my substrate. Is there a sturdy method of doing so? Thank you in advance.

Badges
Science topic

More Zhuxiao Gu's questions See All

Questions of antibodies selection?

Hi there, I'd like to use immunocytochemistry to determine a surface protein expression on mouse cell. The primary antibody I have is mouse anti mouse, and the secondary antibody I have is goat...

15 July 2024 6,008 5 View

How to do single-trial ERP analysis?

Single-trial ERP analysis provides a way to extract the amplitude of each trial rather than one certain condition...

01 July 2024 6,553 2 View

Why did the simulated load-displacement curve of beam keep increasing and didn't decrease (ABAQUS)?

Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...

29 June 2024 6,192 2 View

Is there a rapid method to determine the agar content in microalgae?

Traditional methods for the determination of agar content in macroalgae need a lot of time, if there is a fast and accurate agarine content detection method will greatly promote the development of...

21 March 2024 3,306 0 View

Is it possible to do the 1-1-2 multilevel model in R?

I am constructing a multilevel model. To specify, I have two independent variables, one in Level 1 and another one in Level 2. The moderate variable and dependent variable are both in Level 2....

25 February 2024 9,874 3 View

How can I calculate the ICC1, ICC2 for each company?

I have a dataset that includes 1900 companies. Also, I investigated 10 employees for each company. There is a question about the risk preference of each employee. At now, I need to calculate the...

13 December 2023 9,571 5 View

Did someone used E. coli cell-free system in 384 plate?

I'm gonna do the E. coli cell-free experiment in 384-well plate. But I have trouble with plate choice. E. coli cell-free experiment doesn't need a sterile enviroment, but I think plate should be...

12 November 2023 1,990 0 View

Anomalous initial charging behavior of LiFePO4 half cell assembled with Li metal?

Hello! I just started learning battery research. I'm working on to get myself used to coin cell assembly process and to achieve reproducibility of sample preparation. Here's my coin cell...

11 October 2023 868 2 View

Does repeated use of agarose gels affect the pre-staining gelred in the gel?

I only used 2 wells of 12-well gel for my first electrophoresis. Can I reuse the remaining wells at the end of this electrophoresis? Could the gelred dye in the gel have been affected by the...

20 September 2023 9,803 1 View

Is it possible that an antiviral compound inhibit the virus infection but did not inhibit the pseudotype-virus and replicon?

Hi, I have identified an antiviral compound that showed antiviral activity against feline coronavirus. Now, I am trying to figure out its antiviral mechanisms. First, I try to figure out which...

01 May 2023 8,496 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

What is the solvent for 8YSZ nano material?

I need to do some experiment with it in liquid form.

07 August 2024 613 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

Hi, please what is the best tool on Aspen plus that can help me get the best inlet temperature and pressure for cryogenic distillation?

I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...

06 August 2024 4,611 0 View

How much Yeast should we add to fermentation media?

I have prepared a liquid broth containing Yeast (S. Cerevisiae) that i need to add from it to fermentation media of lignocellulosic hydrolysate. I need to know based on what parameters do we add...

06 August 2024 662 1 View

What is the best protocol for freezing the rat brain in preparation for protein detection by Elisa ?

What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?

01 August 2024 1,722 1 View

How is the bacterial genome's high protein count verified as genuine despite 800+ contigs and good metrics (98.55%completeness, 0.68% contamination)?

Given that the bacterial genome has over 800 contigs, but its quality metrics are good, with a completeness of 98.55% and a contamination of 0.68% as assessed by CheckM, what specific validation...

01 August 2024 1,514 1 View

How to treat monolayer culture cell line with essential oil?

Hi all, may I ask you for advice about treating monolayer culture cell line with essential oil. Due to the hydrophobic character of the oil, I am concerning how can it equally affect to all the...

31 July 2024 5,301 2 View