want to prepare TiN
Heating TiO2 in nitrogen at temperatures >=1000 degC will lead to some loss of oxygen. The product formula will be somewhere between Ti2O3 and TiO2, depending on temperature, purity of the nitrogen, and time. You won't get TiN this way.
Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?
06 August 2024 980 5 View
Hello everyone! I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...
05 August 2024 5,729 2 View
Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...
03 August 2024 5,358 0 View
need to open an account to upload my published papers
01 August 2024 9,255 1 View
All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.
01 August 2024 589 4 View
I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...
01 August 2024 9,227 1 View
Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...
30 July 2024 9,824 2 View
N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.
30 July 2024 7,233 4 View
Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...
30 July 2024 906 2 View
Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...
29 July 2024 7,198 9 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
I used Aqua regia to clean Au nanoparticles in the used glassware. But for some reasons, it is not heating up upon mixing. The color did change from no color to light orange. The Au NPs on the...
25 July 2024 4,390 0 View
What is the heating temperature that I can use to deactivate enzymes in bacterial extract exopolysaccharide without loss of the bioactivity of EPS? Hi I am trying to make the purification (by TCA...
22 July 2024 5,334 6 View
For which types of polymers, the crystallization peak in heating cycle of DSC test can be observed and for which types cant? In another word, when this exothermic crystallization can be observed...
18 July 2024 348 3 View
i need to know the required time
15 July 2024 4,796 2 View
Hello everyone, I am trying to encapsulate an essential oil in the liposomes using the heating method and encountering some issues. I am following the protocol described below, but my solution...
10 July 2024 4,083 3 View
Salam everyone, So I am trying to extract DNA from isolates of clinical samples of staphylococcus aureus, I am using a QIAamp UCP kit. I followed the same manufacturer protocol and used Qubit to...
03 July 2024 3,892 1 View
I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...
26 June 2024 2,358 0 View
I would be grateful if someone could guide me how to get the input and output pressure in the compressor used in solar heat pumps? For example, in this article Annual comparative performance of...
12 June 2024 8,985 5 View
Hi, I've recently started using the FLUOstar Omega plate reader to perform some basic bacterial growth curves. Before putting the plate in I've been trying to use the temperature incubation...
06 June 2024 5,923 0 View