I am unable to get the min. values of the type of stress mentioned, everytime I complete the simulation. How's it done?
Please see the value of stresses here below;
Please suggest.
what do you mean, you already have zero stress, please note that
Von Mises is always positive.
Dear Arun Raj Khanna
In abaqus visualization module go to the contour option then select limits put tick on show location for min box.
I hope this help you
Regards
Balasaravanan K
You can get the max and min values from: Viewport Annotation Options-Legend (Show min/max values).
It's done. Thanks to all :)
May I ask if anyone know what does the 75% under S, mises means ?
Victor Ng
https://abaqus-docs.mit.edu/2017/English/SIMACAECAERefMap/simacae-t-resaverage.htm
i am getting von mises stress values but i cant see the red colour in the image
Jasim Abdullah
in the image it is not showing the red colour can you help me to sort out that error
I am working on transparent/translucent zirconia-based ceramics. In many papers, I have seen that they are reporting both In-line transmission (%) & Total transmission (%) value of...
20 February 2021 9,405 6 View
Hello everyone, I want to perform some gaussian calculations and want to use Materials studio for my research work. Can anyone guide me how to get access to supercomputer resources in India for...
15 February 2021 8,264 3 View
I used Type169 for data exchange between Python and TRNSYS. Unfortunately, facing the following error. No proper documentation is available for this part. TRNSYS Message 105: A TYPE was called in...
14 February 2021 5,577 1 View
Can Amine (such as Et3N) be used as solvent as well as base for the Sonogashira Coupling? How to decide the amount of solvent to be used in any reaction? Does the amount of solvent affect the...
14 February 2021 4,018 3 View
I'm working on gram negative i want to use any natural extract (plant extract) or triple drug combination against its biofilm formation.
14 February 2021 1,403 3 View
Dear community, I am currently writing my master's dissertation. As a part of the method, I have to include views (interview) of experts for the empirical analysis. The problem is I have not...
31 January 2021 3,438 3 View
I'm a new siesta learner, I'm working on lithium-ion batteries, I have calculated adsorption energy but i am not able to calculate diffusion barrier of Li ion. kindly help me how to calculate...
14 January 2021 2,688 1 View
Suggest some good journals having Impact factor more than 3 which is not an open access one for alternative and complimentary medicine?
11 January 2021 7,782 1 View
In alkaline lysis solution3 acetic acid should be used to adjust pH according to protocol. Can I use hcl instead of glacial acetic acid? Will there be any change in composition of solution?
08 January 2021 7,764 3 View
I want to extract plasmid dna from bacterial culture guide me what will be the most appropriate method.
05 January 2021 1,118 14 View
I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...
01 March 2021 10,078 1 View
I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...
01 March 2021 6,661 3 View
I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...
01 March 2021 736 3 View
Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...
01 March 2021 9,511 3 View
Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...
28 February 2021 3,442 2 View
I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...
28 February 2021 4,841 3 View
I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...
28 February 2021 5,415 1 View
I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...
27 February 2021 6,818 3 View
Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...
25 February 2021 9,936 2 View
I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...
24 February 2021 4,908 5 View