Up to what percentage DMSO can be used so that it does not have any toxic effect?

12 October 2023 1 10K Report

Up to what percentage DMSO can be used so that it does not have any toxic effect

Depends on the route of administration. For I.P I have used up to 10% with no adverse toxicological effects. For parenteral administration I would not go above 5%. All this is for experimental animals, no idea in humans...

Badges
Science topic

Similar topics
Chemistry
Chemicals
Solvents

More Sanhita Saha's questions See All

Is this 6GHz wifi antenna create complexity at the time of febrication?

I have design a 6GHz antenna for wifi.The feed line width is 2mm and there are 2 parasitic elements beside this feed line with 1 mm gap.Is there any problem at the time of febrication?

04 February 2021 9,241 3 View

How can you make a PEDOT:PSS film using the doctor blade technique?

I have been trying to make an even PEDOT: PSS (PH1000) film with the doctor blade technique (tape casting) with varying results. I have been using a silicon substrate that's treated with piranha...

01 February 2021 8,506 5 View

How robust are open source soil moisture sensors connected to an arduino board for field monitoring?

Seeking recent experiences in the development and deployment of low-cost soil moisture sensors (ideally under $50/sensor) connected to arduino-based dataloggers. What is the longetivity of the...

19 January 2021 6,256 2 View

How to separate a mixture of organic acids by GC?

I would like to develop a method for analysis of many organic acids in the same time. how to separate the chromatographic peaks of each one?

20 December 2020 8,399 3 View

Should I keep the missing values > 50%?

I have a data set of 771 sample size. But some of the variables (laboratory findings like ALT, AST, creatinie level) have more than 50% missing values. Should I drop those? But I think those...

13 December 2020 4,847 3 View

How to Strip off HSQ( Fox 16) after etching?

We are finding a hard time to strip of residual HSQ ( Fox 16) after using it as a mask in etching? We are coating 600 nm thick HSQ and writing with 3000 microC/cm^2 dose at 1 nA current. We are...

08 December 2020 5,452 2 View

Why the oral cancer cell line from metastatic tongue origin is showing less aggressive property?

I am working with oral cancer cell line SCC090 (ATCC). As per ATCC data sheet it is originated from metastatic tongue. It's primary site is not mentioned. Due to the origination from metastatic...

08 December 2020 5,674 3 View

In case of larger sample size (more than 700 sample) can I do t-test though the data is not normally distributed?

My sample size is more than 750 but sk test is showing non-normal distribution. The variables have several outliers but I shouldn't remove those. In that case what should I do? t-test or other...

06 December 2020 1,285 19 View

Why the western blot of HIF1alpha of the whole cell lysate shows intense band under normoxia without any induction of hypoxia?

I am working with oral cancer cell lines and trying to find the expressional changes of HIF1alpha under different experimental treatment. I am getting intense band of HIF1alpha in the western blot...

29 November 2020 5,707 3 View

How to calculate in-plane lattice strain for 2D material?

I am working with h-BN and need to find out the strain due to in-plane lattice constant. The famous Williamson-Hall method may not be applicable here as it analyzes XRD for calculation of strain...

19 October 2020 7,386 4 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

Bought HUVEC from Invitrgen.need to revive it.expected it is cryofreezed in DMSO.Do I need to remove the DMSO for plating the cell for the 1st time?

After I cryofreeze the cell do I need to remove the DMSO for culturing the cell for next passages .

28 February 2021 7,738 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Is there anyone who experienced with cytotoxic effect of Hoescht 33342 dye?

Is Hoechst toxic to cells? In general, it is known as non-toxic. I am working with dsRED MDA-MB-231 cell line. I applied it for my PDMS-based microfluidic platform, for this reason, I incubated...

26 February 2021 9,119 3 View

Does anyone have any ideas why drug-resistant malaria is increasing in Southeast Asia even when those drugs are no longer used?

When dealing with bacterial toxins, there are three varieties of microbes that develop in your petri dish: toxic, resistant, and susceptible. Initially, there are only toxic and vulnerable...

21 February 2021 6,084 5 View

How to dilute Toxin-DMSO solution?

I have a concentrated solution of a toxin(50 micromolar) in DMSO 100%. I need to dilute it inorder to dilute both the toxin and DMSO wich can be toxic to cells. Which would you guys recommend to...

19 February 2021 7,447 2 View

How to successfully revive cells stored at -80 degree C for a year?

I am working on C6 cells along with other neuronal cell lines. We have preserved the cells in 90%FBS and 10% DMSO solution. We are reviving the cells after a year and cells are either not binding...

18 February 2021 4,499 1 View

How can I make sure that BCTC doesn't fall out of solution/form DMSO crystals when treating cells?

I resuspended my BCTC as described on the bottle at 10mg/mL in DMSO. However, I can see the formation of crystals which I can only assume are DMSO and that the drug is precipitating out of...

14 February 2021 5,633 1 View

Can anyone suggest a way to dissolve insulin which is for rat/mouse injection?

We are trying to inject insulin to rat or mouse, but the insulin we've got is powder, and there are many ways for dissolve, like in saline, PBS, DMSO, or in Tris-HCl, can anyone give us a...

13 February 2021 8,426 10 View

DMSO concentration in cell culture? Precipitating while PBS is added?

I am testing a compound on RAW 264.7. the compound is soluble in DMSO. but to ensure that final concentration of dmso is not more than 0.1%, we are first dissolving it in dmso and then diluting it...

11 February 2021 1,136 3 View