UMAT user subroutine for concrete, capable of cyclic ?

12 December 2015 1 10K Report

Has anyone created a . I am interested in modeling a UMAT user subroutine for concrete, capable of cyclic loading composite steel frame with concrete slab, and the "Damaged Plasticity" model in ABAQUS has convergence issues with the cyclic analyses. If it is possible to get a copy of your UMAT, I am very interested.

Thanks

Assad M

Loginy Loganathan

Hi. Did you manage to do this?

Badges
Science topic

More Ardeshir Mm's questions See All

Which diagram for the confined concrete by a steel tube should I use in concrete damaged plasticity model in ABAQUS?

Which diagram for the confined concrete by a steel tube should I use in concrete damaged plasticity model in ABAQUS: uniaxial compressive diagram or confined concrete diagram?

10 November 2015 4,927 0 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View