I made a TENG by PVDF and nylon 66, both have Al electrode and connect to the oscilloscope by Cu tapes. When I test the Voltage, it only shows 2 or 3 V. What did I do wrong? Can you give me some advice how to improve them to about 100 V?
This is a diagram of an adsorption device with 2 adsorption columns, the input air is to the far left and the product is on the top right corner. Can someone tell me its working principle?
11 April 2020 2,066 0 View
I read a paper, that said they had dissolved PS by putting 7.5wt% PS in 46.25wt% HFIP and 46.25wt% DMF, stirring overnight. Is that true? How can I dissolve PS for electrospinning?
01 January 1970 9,930 3 View
I started the limonene oxidation process inside an autoclave at 150 Celsius Degree, TBHP as initiator, solvent: ethanol. However, the GC-MS showed the oligomerization of TiO2. As far as I know,...
01 January 1970 6,434 0 View
Would you kindly show me how to electrospin PDMS? I have never learnt about this technique, thank you.
01 January 1970 9,851 2 View
I have just bought a core-shell electrospinning system. Therefore could you provide me some simple examples to make core-shell fibers and to get used to the machine, especially fibrous polymers?...
01 January 1970 5,385 3 View
According to some advises on researchgate, I bought another electrospinning pump for the co-axial technique. However, after I had installed it, the axle still rotated yet the square was not moving...
01 January 1970 6,572 0 View
I am doing experiments about oxidation process from limonene to limonene glycol, but the product are some limonene oxide (which I don’t want). These are the chemicals I have: -Catalyst: CuY...
01 January 1970 7,710 5 View
I am making PVDF solution for electrospinning, I only have DMF and acetone as solvents, so can you tell me the optimal conditions for this process? (ratio, temperature, time, stirring speed). Any...
01 January 1970 3,117 6 View
My TENG (PDMS-Copper) can fabricate about 24 Volts by 2.45 N at the frequency of nearly 1 Hz. However, the average current value is only about 100 nA. How can I increase the current, I only need...
01 January 1970 245 4 View
Hi, can you kindly provide me with some simple processes for fabricating a self-healing film based on Diels-Adler reaction? I have already known about the basic principle, diene with dienophile...
01 January 1970 8,884 1 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,141 3 View
I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this
05 August 2024 7,902 3 View
In my tests with a sliding mode triboelectric nanogenerator, I have observed maximum power output at three different resistance values. How should I determine which resistance provides the peak...
05 August 2024 5,049 0 View
I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from experts in the field. If you are an expert or researcher working on...
02 August 2024 2,627 1 View
I want to know that n-doped side of solar cell is connected with positive or negative electrode.
20 July 2024 1,348 2 View
I studying PhD course in Urban design for Health. I need to know in some fileds: residental block, green open space and Transport TOD. I need connect with expert in that fileds.
14 July 2024 1,892 3 View
We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...
09 July 2024 5,123 4 View
"Today several adjectival phrases have been used to describe English like ‘International Language’, ‘Lingua-Franca’, ‘Language for Globally Connecting’, ‘Library Language’, ‘Official Language’,...
01 July 2024 8,406 5 View
Sharing research simultaneously on both platforms
28 June 2024 9,120 2 View
I have made a PVDF film and now I am trying to see the film's performance. I have made contacts on the film with the help of silver paste and attached copper strips as electrodes. But, I am not...
24 June 2024 8,671 0 View