How does this Adsorption device work?

12 April 2020 0 2K Report

This is a diagram of an adsorption device with 2 adsorption columns, the input air is to the far left and the product is on the top right corner. Can someone tell me its working principle?

Badges
Science topic

Similar topics
Solid State Physics
Devices

More Tran Khanh's questions See All

How can I dissolve Polystyrene for electrospinning?

I read a paper, that said they had dissolved PS by putting 7.5wt% PS in 46.25wt% HFIP and 46.25wt% DMF, stirring overnight. Is that true? How can I dissolve PS for electrospinning?

01 January 1970 9,930 3 View

Oligomerization of TiO2 in the limonene oxidation process

I started the limonene oxidation process inside an autoclave at 150 Celsius Degree, TBHP as initiator, solvent: ethanol. However, the GC-MS showed the oligomerization of TiO2. As far as I know,...

01 January 1970 6,434 0 View

How to electrospin PDMS?

Would you kindly show me how to electrospin PDMS? I have never learnt about this technique, thank you.

01 January 1970 9,851 2 View

Easiest Core-shell electrospinning

I have just bought a core-shell electrospinning system. Therefore could you provide me some simple examples to make core-shell fibers and to get used to the machine, especially fibrous polymers?...

01 January 1970 5,385 3 View

Electrospinning pump malfunction

According to some advises on researchgate, I bought another electrospinning pump for the co-axial technique. However, after I had installed it, the axle still rotated yet the square was not moving...

01 January 1970 6,572 0 View

Limonene to limonene glycol

I am doing experiments about oxidation process from limonene to limonene glycol, but the product are some limonene oxide (which I don’t want). These are the chemicals I have: -Catalyst: CuY...

01 January 1970 7,710 5 View

How can I dissolve PVDF in optimal condition? (ratio, temperature, time, stirring speed?)

I am making PVDF solution for electrospinning, I only have DMF and acetone as solvents, so can you tell me the optimal conditions for this process? (ratio, temperature, time, stirring speed). Any...

01 January 1970 3,117 6 View

Triboelectric nanogenerator low current.

My TENG (PDMS-Copper) can fabricate about 24 Volts by 2.45 N at the frequency of nearly 1 Hz. However, the average current value is only about 100 nA. How can I increase the current, I only need...

01 January 1970 245 4 View

Simple self-healing Diels-Adler processes.

Hi, can you kindly provide me with some simple processes for fabricating a self-healing film based on Diels-Adler reaction? I have already known about the basic principle, diene with dienophile...

01 January 1970 8,884 1 View

Optimal Nylon 6,6/Formic Acid Electrospinning Set up.

Can someone give me some parameters about the electrospinning process of the Nylon 6,6/Formic Acid solution? (concentration, flow rate, Voltage, etc.) I tried Nylon/Formic Acid 20wt% (4 grams...

01 January 1970 7,101 11 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

RNA Extraction Using Hot Borate Method No Longer Working?

I've been performing RNA extraction on cotton petiole tissue for a few months now using the method described in the following paper, a derivative of the typical hot borate method...

08 August 2024 9,882 2 View

Can I use a HisTRAP column for affinity chromatography?

I'm working on selecting antibodies against a recombinant protein that has a His-tag. My idea is to first bind the recombinant protein to a HisTRAP column and then use this column for an affinity...

07 August 2024 505 3 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

Hi, please what is the best tool on Aspen plus that can help me get the best inlet temperature and pressure for cryogenic distillation?

I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...

06 August 2024 4,611 0 View

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

In the presence of VERY high concentration (1000 ppm) of silicon, the adsorption isotherms of arsenic are showing anomalous trends, why so?

I conducted an adsorption experiment of arsenic on soil in the presence of different doses of silicon as competing ions to see the effect of silicon on arsenic adsorption and desorption. I took 5...

03 August 2024 6,500 3 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View