I NEED TO KNOW THE DIFFERENCE BETWEEN (CONCRETE SMEARED CRACKING) AND (CONCRETE DAMAGED PLASTICITY) IN ABAQUS PROGRAM.
Use the CONCRETE SMEARED CRACKING.
Good question.. Please share me the best answer might you trust...
Regards…
In plant tissues
07 August 2018 4,314 0 View
Hello, I'm working in a research project required a survey of Egyptian public sector enterprises Implemented/under implementation of ERP application.
09 October 2017 5,490 0 View
While i`m analysing a solid shear wall subjected to vertical and horizontal loads in ABAQUS (STATIC ANALYSIS) , I got the problem in the attached file when i checked the data of my job. Please...
31 December 2016 7,758 2 View
I need the equation(s) describing the relation between stress and strain in ABAQUS for concrete (The curve that exists in the ABAQUS manual) for concrete damaged plasticity (CDP) model ?
31 December 2016 9,838 1 View
While i`m analysing a solid shear wall subjected to vertical and horizontal loads in ABAQUS (STATIC ANALYSIS) , I got the problems in the attached file when i submitted my job. Please...
31 December 2016 4,882 6 View
When i plotted the relation between compression damage parameter (dc) and inelastic strain of the verification model given in ABAQUS VERIFICATION MANUAL for CPD model in EXCEL , i got the third...
31 December 2016 1,899 2 View
My research is about investigating lateral deformations in shear walls with openings , I need to know which model is more appropriate for that purpose ..Smeared crack concrete model or Concrete...
11 December 2016 5,352 5 View
Where is it preferable to locate construction joint in reinforced concrete slabs and beams and why are these specific lacations
07 August 2016 1,112 5 View
I need to know the difference between column and wall definition in terms of cross sectional dimensions
07 August 2016 7,021 0 View
I need to know what is the suitable constitutive model for reinforced concrete in shear walls with openings in the FEM Program ABAQUS. The shear walls are with different openings configuration and...
06 July 2016 3,162 3 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...
20 July 2024 9,153 11 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View