Nice Greeting,
could you please assist me to figure out how could increase the number of out put point for the time history curve (velocity vs time curve) that obtain by Aaqus software?
thanks in advance
Hye Hiba al-adhami, you can refer to the link below ( Abaqus documentation) Hope it will be helpful. Thanks
http://www.egr.msu.edu/software/abaqus/Documentation/docs/v6.7/books/usi/default.htm?startat=pt03ch14s12hlb03.html
journals Scopus biology quick publication
11 December 2018 4,233 5 View
Microscope examination Immunological method ( Trichomonas Rapid test) Culture method Staining method pH measurement Whiff test using Hematology Analyzer for an account pus cells molecular...
10 November 2018 9,933 16 View
Do you think acute diarrhea in infants Affect the development situation For physical equipment in infected infants?
09 October 2018 6,219 3 View
parasitology
04 May 2017 7,710 7 View
molecular
04 May 2017 7,214 7 View
04 May 2017 9,488 4 View
04 May 2017 10,218 5 View
Nice Greeting, I am trying to figure out how could trigger the data acquisition due to an external applied pulse load by specify a specific threshold "pre triggering time"? I appreciate any...
30 December 2016 4,055 6 View
Nice Greeting, Could you Please assist me to figure out why could not find the DAQ assisstant in the lab view input, however I install the DAQmx that compatible with the labview version 2015 ? I...
11 December 2016 7,387 2 View
Hello all , I am wonderring if there is any way to extract the MATLAB code for the ANN trained by using nntool in MATLAB. Please, could any MATLAB user assist me to do so? Thanks, Hiba
11 December 2016 3,145 0 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View
I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...
16 July 2024 8,436 0 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View