What is the best method to analyze data statistically?

What is the best method to analyze data statistically?

02 March 2019 4,967 5 View

How i can make optimization for two factores and five levels for each factor by RSM in Minitab 2017 program?

How i can make optimization for two factores and five levels for each factor by RSM in Minitab 2017 program?

31 December 2018 9,323 1 View

Are there Composite Materials that manufacture from one material ?

sandwich structure is composite materials make from two materials or one.

09 October 2017 1,081 0 View

What is the end time in ANSYS explicit dynamics?

How calculate end time in ANSYS explicit dynamics?

09 October 2017 4,616 0 View

How can I draw and rotate twin screw machine by Ansys workbench 15 ?

How can I draw and rotate twin screw machine by Ansys workbench 15 ?

11 December 2016 3,594 1 View

Can you use finite element method to simulate an analyze magnetic nanoparticals?

01 January 1970 248 1 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How do you write a simplified C block code of this average-current control on PSIM?

This is a Buck (step-down) Converter and I am new to this program. I need to program with simplified C block and I actually don't know what to do. Can anyone show me how to do this? Or at least...

02 March 2021 8,233 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Do you know good and user-friendly programs to measure plant quantitative traits?

For my research i will need to measure plant quantitative traits (especially leaves area and roots length, but would be nice to add some more information). I recently discovered...

01 March 2021 5,035 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View