Sn+xLi++xe−↔LixSn (0≤x≤4.4), according to this equation, the Theoretical specific capacity of Sn is 993.4 mAh/g. Please, can anyone explain why 4.4 is in the equation?
Toma Stankulov, thank you, but I asked to understand, not to take a note
I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.
02 August 2024 6,789 4 View
I need to plot cycle number vs. capacity with multicurrent density. please let me know if my steps are right or not as the below picture
14 July 2024 7,702 2 View
I prepared h-BN by hydrothermal methods by boron anhydride and urea after hydrothermal I was heated at 800 temps for 12 hours after that my sample stuck to the crucible the third time, and the...
15 May 2024 7,354 0 View
I fabricated nanocomposite using the sol-gel method with a mole ratio (1:1) I want (10g) of the final product ZnO-TiO2( molar mass-161.246g/mol) the calculations of the raw materials are as...
13 May 2024 1,731 5 View
i prepared graphene oxide by modified hummers method
13 May 2024 5,162 2 View
MgO NPs were synthesized by sol-gel method. i got Raman peaks at 1022 and 1400
09 May 2024 1,027 3 View
I need this synthesis by hydrothermal method
06 May 2024 1,866 4 View
Actually, I prepared a large amount of MgO, after aging I kept it in a hot air oven at 120 for 12 hours, but there was still moisture there, then I kept it again in a hot air oven at 120C for 6...
05 May 2024 6,280 2 View
because I prepared magnetite by sol-gel method, I got XRD peaks, but for Raman, I didn't get a peak at the range 600cm-1, should I change the wavelength of the laser, or what do I have to do
05 May 2024 2,244 4 View
microwave
16 April 2024 10,006 4 View
I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...
03 August 2024 5,384 0 View
Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...
03 August 2024 5,358 0 View
I am an Mphil research student and looking for high impact factor battery related journals to download and read research articles to improve my knowledge and get new ideas in the field of battery...
01 August 2024 6,516 2 View
I have attached the charging curve from the battery tester for review. I need help on what is happening
21 July 2024 6,898 2 View
Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?
10 July 2024 8,763 0 View
I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...
08 July 2024 7,327 4 View
The difficulty lies in how to miniaturize the battery. The sample holder is only 6.5mm, which means that the width or height of the battery cannot exceed 6.5mm (the height is about 3cm). I hope...
05 July 2024 8,141 0 View
In Zn-Air Battery, how to plot Potential vs current density(mA/cm-2) in EC-Lab softare/BioLogic instrument. Please suggest. plot of the ref....
04 July 2024 3,807 2 View
I'm currently exploring the economic implications of solar PV curtailment versus the installation of battery energy storage systems (BESS). Specifically, I'm interested in recent publications or...
27 June 2024 6,423 2 View