How to judge and prove the uniqueness of the solutions to the following two matrix equations?

It is about the matrix equation AX=B, where a, b c in A and B are independent elements, X should be made of constants. Case 1 A=[a b 0;0 0 c]; B=[a b 0 0;0 0 c c]; The solution is X=[1 0 0 0;0 1...

16 February 2021 5,698 3 View

What is the method of removing RNase contamination from a filter paper surface?

I am working on a biosensing project on paper substrate, however, it is found that the RNase contamination occurs on the filter paper. Might I ask is there any method to clean the paper surface...

12 February 2021 3,926 3 View

Is there any method that we can electrochemically oxidize a powder?

I am working with a material which is sensible to water and oxygen, I would like to oxidize this powder either chemical or electromagnetically. Does anyone knows a method to electrochemically...

09 February 2021 2,944 3 View

What is causing the raw fluorescence to be negative?

Hi everyone, I would really appreciate it if someone can tell me when and why a raw fluorescence starts below zero. In the picture attached below the blue colour curve starts from a negative...

09 February 2021 4,642 3 View

Regarding immunology, transmissivity, herd immunity and vaccines in Sars CoV-2?

This is a follow-up on an earlier question regarding mechanistics of vaccines: why current vaccines don't block transmission. In summary, they don't engage mucosal immune cells to produce IgA....

08 February 2021 8,321 3 View

How can I enter the load increment values to the Abaqus?

In Abaqus I know that there are two methods for incrementation (Automatic and fixed incrementation). I want to control the incrementation by myself. I want to input the values of load increment...

03 February 2021 6,943 3 View

Distortion problem in Abaqus explicit?

Dear all. I'm modeling the RC column with cyclic displacement by Abaqus-Explicit. The concrete model used Concrete Plastic Damage model. However I'm facing with a error about the excessive...

01 February 2021 7,726 1 View

I am finding a lot of cellular debris in the culture flask? What are the reason behind it?

I am facing a problem that cellular debris observed in my SHSY5Y cells. I have seeded the cells in DMEM media with 10% FBS in T-25/ 60mm dish (antibiotic used PEN-Strepand gentamycin). I have also...

17 January 2021 3,074 3 View

How to make sure each cavity modes with same E-field distribution in COMSOL simulation?

In COMSOL Application Library, there is case about waveguide adapter. But there are some questions: 1) In boundary mode analysis, it just set to find only 1 mode and the S-parameter is...

12 January 2021 9,383 2 View

What is the reason for discontinued Stage II fatigue crack growth in pearlitic steel?

Conventionally, the process of Stage II fatigue crack growth is governed by Paris law with less microstructural effect. When fatigue crack growth test was carried out for pearlitic steels ( both...

03 January 2021 7,075 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View

Are there alternatives to the Devarda alloy when estimating nitrogen?

Are there alternatives to the Devarda alloy when estimating nitrogen? devarda alloy is reducing the nitrate to ammonium

15 February 2021 8,838 3 View

Passivation of chromium cast Iron in high temperature?

14 February 2021 2,157 3 View

How can we quantify martensite in Ferrous and Titanium alloys?

How can we quantify metastable phases like martensite in Ferrous and Titanium alloys, in relation to their stable counterpart For example in EBSD, XRD, Optical? Eg, Martensite and Ferrite maps.

09 February 2021 7,572 3 View

About forging of Mo Alloys ?

Hello dear Academicians, I am working on the forging of Mo alloys, but I wanted to consult you on an issue I could not solve. Mo is easily oxidized during forging and MoO3 is formed. Is it...

09 February 2021 1,989 3 View