Matlab fireworks code for extracting solar cell parameters?

I am currently working on extraction of the parameters of the photovoltaic cell using fireworks algorithms. But unfortunately I find it hard to code these algorithms. Please is what you can send...

02 December 2020 3,418 4 View

Troubleshooting pcr amplification with touchdown program: can anyone help please ?

10 July 2020 1,234 11 View

Is there a need of SeqScape soft ware and Variant reporter soft ware in MLPA data analysis process ?? Or it is only the coffalyser which is needed ?

Is there a need of SeqScape soft ware and Variant reporter soft ware in MLPA data analysis process ?? Or it is only the coffalyser which is needed ?

16 March 2020 9,640 1 View

Can enzyme characterization be done using RSM?

I want to characterize an enzyme.. In stead of one factor at a time procedure i was wondring if it can be done using response surface methodology... Is there any publications for enzyme have been...

30 December 2019 2,807 2 View

No title

04 December 2019 3,507 2 View

Hi, What is the size of NADPH enzyme in Dalton? It's molar mass is 745.4 g/mol?

I am working on a project involved drug metabolism by NADP/NADPH enzyme. I want to remove the enzyme from my reaction mixture. I am looking for the amicon centrifugal concentrator to remove that...

18 November 2019 1,141 3 View

How could I include an interface in Sdevice simulation of traps??

I am trying to simulate traps in TFET interfaces between oxide and silicon using sentaurus Sdevice. I included the traps in command file as follow: Physics (MaterialInterface = "Silicon/HfO2")...

16 September 2019 9,039 3 View

How to prepare a suspention of bacterial concentrate equal to1 x 106 /ml?

this suspention is prepared for DNA extraction

15 August 2019 8,871 3 View

Atmospheric correction of raw image from local satellite?

i need to make an atmospheric correction of raw images from a local satellite but when i use QGIS it asked me for the name of the satellite i need to know if there a tool that takes a raw image...

01 December 2018 6,047 4 View

I have old blood samples stored at 4 degrees since 6 months . What method of DNA extraction can I use to obtain high yield and good quality ?

I have some old blood samples stored at 4 degrees since 6 months . What method of DNA extraction can I use to obtain the highest yield and best quality ? . And If I am using modified salting out...

19 February 2018 8,986 5 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View