The different possible ordering between several independent transitions, is it the unique cause of the state explosion problem ?

25 July 2018 1 142 Report

The different possible ordering between several independent transitions in Transitions Systems, is it the unique cause of the State Explosion Problem ?

Mihai Lica Pura

I think there is also the case when for the same input/condition, multiple transitions can fire, so each case should be separately considered.

Badges
Science topic

Similar topics
Mathematical Sciences
Graphs

More Oussama Hayane's questions See All

Looking for help on sem image analysis?

Hello I am conducting a microstructural analysis of a soil treated with lime. The following sem images are of the untreated s1 and treated soil s3. The untreated soil contains quartz calcite...

01 August 2024 572 0 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

How to Trace velocity plot u(t) using comsol?

Hello How can I get the velocity plot u(t) of a rising bubble using COMSOL like in this tutorial...

24 June 2024 9,441 6 View

How can we select the best energy storage system for our Microdrid, and what are the best energy storage devices to be included?

There exist a wide range of technologies used for energy storage such as electrochemical (batteries), electrical (supercapacitors), mechanical,...etc. What are the best and the most efficient...

17 May 2024 3,412 1 View

Specific capacitance values?

Why specific capacitance calculated from cyclic voltammetery is different from the one calculated from charge-discharge? Ps1: I used the same potential window. Ps2: the charge-discharge curve is...

18 April 2024 9,691 1 View

The amount of water needed during the impregnation?

How much water is typically used during the impregnation step? is there any relationship between the weight of carbon and the amount of water?

12 April 2024 2,952 0 View

I need help designing an H Infinity controller to control a wind energy conversion system ?

What is the best approach to design an H infinity controller for a linear model of a wind energy conversion system, with the goal of simulating it in Simulink? Any specific methods or tools...

26 March 2024 4,008 1 View

Time of N2 injection during chemical activation?

Dear researchers, during chemical activation, when should i start injecting N2 to the precursor? is it at the same time when start heating or until reaching the desired temperature ? thanks in...

23 February 2024 1,307 9 View

How to repair a furnce alumina tube?

the furnace i am using for activation has been damaged, the alumina tube broke , i need a good glue to fix it!

12 November 2023 5,248 1 View

Why i am getting no dischage even after long time?

during GCD, i am seeing no discharge after long time of charging?

12 November 2023 7,295 12 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View