How can I define "Heat Transfer in Fluids" for water that flows through an air domain and reaches a Wetted Wall in COMSOL Multiphysics for a 2D model?

Hi all, I hope everyone is doing well and is in good health. In the simulation it is needed to change the phase of water that flows through an air domain. So I used Laminar Flow and Level Set...

25 November 2020 365 4 View

How to propagate the EMC Virus in L929 cell line?

04 October 2020 6,705 2 View

How can I interpret a NMR with so much noises and peak overlaps?

Ideally peaks should be separated and having a somewhat symmetric pattern but could any one give me a help with reading H NMR with multiple peaks totally mixed up which could not be attributed any...

22 September 2020 3,667 3 View

Any recommendation for a good Machine learning course (with available materials for instructors)?

Hello everyone, I am looking for a good recommendation for a Machine learning course (with available materials). Which one do you suggest? Something that would be up to date with available...

15 September 2020 1,674 17 View

What is a suitable method for measurement of CPE exponent of a coated metal fitted with two time constant circuit?

I encountered a problem for measuring CPE exponent of a coated metal by impedance spectroscopy. The fitting results showed an equivalent circuit with two CPE. The logarithmic diagram of the...

21 December 2018 4,159 5 View

How can I solve the low speed of my simulation in simulink?

I have a multi machine power system, and I had to simulate it by solving differential equations of the whole system in simulink, but the speed of the simulation is very low, how can I do this...

28 October 2014 7,921 15 View

Does anyone have experience with modelling Delamination?

17 August 2014 2,359 7 View

Can anyone help with start, pause, and continue in a simulink model from workspace?

I need to pause a simulation in each time step and after some analysis continue the simulation in matlab software, can somebody help my?

08 December 2013 1,744 3 View

What is the effect of Reynolds number (Subcritical flow regime vs. Critical flow regime) on Galloping?

Does the circulation of vortices in the wake of bluff body with sharp edges such as square cylinder significantly change?

01 January 1970 1,990 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View

Why does two different bioinformatics tools for the same proteins show different subcellular localizations?

During a computational analysis, I found that for a protein of a plant, two different subcellular localizations are seen using CELLO and WoLF PSORT. For example, in CELLO, it identified the...

01 March 2021 6,729 2 View

What is the most suitable server for predicting protein structures in bacteria?

I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...

28 February 2021 4,521 3 View