How can I define "Heat Transfer in Fluids" for water that flows through an air domain and reaches a Wetted Wall in COMSOL Multiphysics for a 2D model?

Hi all, I hope everyone is doing well and is in good health. In the simulation it is needed to change the phase of water that flows through an air domain. So I used Laminar Flow and Level Set...

25 November 2020 365 4 View

How to propagate the EMC Virus in L929 cell line?

04 October 2020 6,705 2 View

How can I interpret a NMR with so much noises and peak overlaps?

Ideally peaks should be separated and having a somewhat symmetric pattern but could any one give me a help with reading H NMR with multiple peaks totally mixed up which could not be attributed any...

22 September 2020 3,667 3 View

Any recommendation for a good Machine learning course (with available materials for instructors)?

Hello everyone, I am looking for a good recommendation for a Machine learning course (with available materials). Which one do you suggest? Something that would be up to date with available...

15 September 2020 1,674 17 View

Software to Predict Antigenicity

17 August 2015 6,400 3 View

How can I solve the low speed of my simulation in simulink?

I have a multi machine power system, and I had to simulate it by solving differential equations of the whole system in simulink, but the speed of the simulation is very low, how can I do this...

28 October 2014 7,921 15 View

Does anyone have experience with modelling Delamination?

17 August 2014 2,359 7 View

Can anyone help with start, pause, and continue in a simulink model from workspace?

I need to pause a simulation in each time step and after some analysis continue the simulation in matlab software, can somebody help my?

08 December 2013 1,744 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to access MSCI KLD Stats and Sustainalytics?

Hello all, I'm currently working on my undergraduate thesis and I'm having difficulties trying to access KLD Stats and Sustainalytics because my campus Airlangga University and apparently other...

02 March 2021 8,525 1 View

Which one carries more value? A research paper in a Scopus Indexed conference proceedings or the same paper in a Journal without Scopus indexing?

I am looking for the suggestion among which one to pick from the above two categories for a research work.

27 February 2021 10,025 1 View

What are the application of Fixed points thoery in Chemistry.?

It is said that fixed point theory has lot of applications not in the field of mathematics only but also in various areas. So I am looking for applications in Chemistry only..

26 February 2021 3,533 1 View

Which indexation is better Scopus or Web of Science?

Both are very repetitive indexing agencies.

26 February 2021 9,455 4 View

What could be reason for getting such type of graph for complex impedance in case of polymer blend films?

Its effect appears in real part of ac conductivity also. Can anyone suggest any reason behind it?

26 February 2021 3,487 3 View

Data Analysis K-S and S-W tests?

Hello, I have conducted analysis where the K-W and S-W have come out as p

25 February 2021 9,648 3 View

How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View

Can I ask did any good platform or journals for learning the calcluation on the reference governors and command governor?

Recently I face some problems with the mathematical ( calculation) on the reference governor and command governor, so I need some help from you all to get which platform or journal can let me...

23 February 2021 7,746 2 View

Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View