Simulation for optimizing MVAR absorption in a 500kV network on a power generation system using ETAP software....?

Muhammad Isnain Wiyasatama @Muhammad-Isnain-Wiyasatama

20 June 2024 0 7K Report

I need advice and suggestions. I want to simulate the operation of a generator to absorb MVAR in a 500kV network. How should I proceed with the simulation using ETAP? How can I set the parameters for the generator, excitation system, and PSS? The specifications of the generator are unit 660MW/776MVA; GT 810 MVA

Badges
Science method

More Muhammad Isnain Wiyasatama's questions See All

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Any one know how to solve with my ETAP 12.6?

I am using ETAP power station 12.6 Enterprise version, and I want to try GIS module, and it shows this comment: " ESRI GIS system not installed! ETAP GIS functionality can't work without ESRI GIS...

26 October 2020 9,826 2 View

Best computer monitor for a digital monochrome camera for DIC/patch clamp?

Hello, We've got a couple of fancy digital cameras to upgrade our patch clamp rigs. Although there are more pixels, while high contrast grayscale pictures look very nice and clean, lower contrast...

22 November 2019 895 3 View

Inverter transformer for solar PV plants sizing?

I asking about the logic behind sizing of transformers connected to solar inverters in utility scale solar PV plants because actually we say all of manufacturers, consultants and EPCs approve...

30 October 2019 6,729 5 View

2x25 kV AC Railway System. How to calculate the Autotransformer Impedance (Ohms) from the AT specifications (Ucc, S, U1/U2)?

Dear all, I am starting to study/model the 2x25 kV AC railway system. When developing the AT short circuit test equations, I come to the equation (Zs+Zc)'=Ucc*U1n^2/S1n. For a typical 10 MVA AT...

11 December 2018 5,419 6 View

Is this the best paper for starting a new research in IoT?

Internet of Things (IoT): A Review of Enabling Technologies,... After thorough study of the paper, I found the following attention-seeking points: The figure 3 depicting the IoT Protocol stack...

11 December 2018 6,122 0 View

How can i synchronize GIS to ETAP software?

how can i synchronize GIS to ETAP software?

09 October 2018 7,486 1 View

How can I calculate transformer resistance and reactance having X/R, %Z, MVA, and kV from primary and secondary voltages?

i need in ohms X and R I have X/R=45 MVA=250 kV prim=230 kV sec=34.5 %Z=12.5

08 September 2018 4,700 1 View

Which software is best equipped for Energy market simulator modeling?

Basically, Power World Simulator has been pretty popular for Energy Market Simulator Modeling (Educational Purpose) due to the incremental cost parameters in generator module and many more...

16 August 2018 2,646 4 View

IEEE 33 bus model in simulink?

I am trying to buitd IEEE 33 bus on Simulink but i still have a problem to specify the source MVA and Voltage IS these valuese are the base values of the system needing a help as soon as possibel

07 August 2018 4,286 1 View

I am using NE 39 bus system's simulink model. From this model, how can I calculate the line current limits?

I am using NE 39 bus system's Simulink model for my simulation purpose. I need the current limits of the transmission lines. From this model, how can I calculate the line current limits? Or from...

31 December 2017 1,427 2 View