Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Any one know how to solve with my ETAP 12.6?

I am using ETAP power station 12.6 Enterprise version, and I want to try GIS module, and it shows this comment: " ESRI GIS system not installed! ETAP GIS functionality can't work without ESRI GIS...

26 October 2020 9,826 2 View

How can i synchronize GIS to ETAP software?

how can i synchronize GIS to ETAP software?

09 October 2018 7,486 1 View

Which software is best equipped for Energy market simulator modeling?

Basically, Power World Simulator has been pretty popular for Energy Market Simulator Modeling (Educational Purpose) due to the incremental cost parameters in generator module and many more...

16 August 2018 2,646 4 View

I am currently modelling a 2.5MW DFIG using ETAP. How do i match the generator parameters with the CKT library in ETAP?

The generator parameters are not compatible with the CKT models available in the ETAP library therefore unable to run transient stability studies. I can provide the available data if needed. Thanks

09 October 2017 3,906 0 View

Design a power factor monitoring device at a point of common coupling (PCC) using ETAP software/Matlab simulink?

Design a block diagram using ETAP or matlab simulink that measures the power factor across a point of common coupling (PCC). The acceptable power factor should be 0.95 and any PCC that is...

18 August 2017 7,463 1 View

Design a power factor monitoring device at a point of common coupling (PCC) using ETAP software/Matlab simulink?

Design a block diagram using ETAP or matlab simulink that measures the power factor across a point of common coupling (PCC). The acceptable power factor should be 0.95 and any PCC that is...

07 August 2017 4,508 1 View

Design a power factor monitoring device at a point of common coupling (PCC) using ETAP software/Matlab simulink?

Design a working model of the monitoring device using ETAP software or matlab simulink in indicating how the device allows 0.95 and above power factor operators to have constant access to the grid...

07 August 2017 7,772 0 View

Could anyone please suggest any ETAP resource for beginners?

I am a beginner to ETAP. Please provide me any resource link which will help me to be proficient on the software.

07 August 2017 4,809 2 View

Anyone have details information for Dynamic models (UDM) in ETAP?

07 August 2017 4,868 0 View

How can I learn used to ETAP ?

07 August 2016 8,224 0 View