Salmon sperm DNA immobilization to 96-well micro-titer plate?

22 November 2021 0 4K Report

Hi,

does anybody know a good protocol for "non-specific" immobilization of salmon sperm DNA onto glass bottom of microtiter plates?

Thanks

Badges
Science topic

More Antonio S Minero's questions See All

¿Are oxygen vacancies in semiconductors capable to change the band gap?

Dear all! Oxygen vacancies do raise negatively the Fermi level by increasing the negative charge in the semiconductor crystal structure. In the case of n-type semiconductors, I wonder if this...

30 July 2024 8,339 2 View

What is the solubility of Iron (+3) in Bismuth Oxide?

Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco

29 July 2024 2,163 1 View

How to express spinors with an arbitrary change of coordinates?

A spinor field in classical differential geometry is defined as a section of a spinor bundle, which is by definition the associated bundle constructed from the spinor representation and the...

14 May 2024 400 0 View

Would it be proper to mark species that do not migrate as "stationary" or "sedentary" ?

I am curious how should i label species in a certain swamp habitat, since i want to make a difference between the migratory and the "stationary" species. Both of the terms i mentioned in the title...

11 May 2024 3,216 5 View

Scotch tape Life Cycle Assessment or production environmental impacts?

Hi all, In the framework of a LCA of perovskite solar cells, I am looking for information about scotch tape, that is used to recover the metals deposited in some layers. Does anyone know of...

18 April 2024 1,678 0 View

Is there any relation between surface area and amorphization degree in high-energy ball-milled activated carbon? The main source could influence?

I milled two activated carbons, with different main sources (shell nutt and bituminous coal). The shell nut AC did not increase in surface area but had some degree of amorphization after milling....

17 April 2024 3,897 1 View

Culturing and mineralization protocol for MC3T3-E1 Sub 14 osteoblasts?

Recently, we have been encountering challenges in our laboratory in achieving satisfactory mineralization of MC3T3-E1 cell line. We would like to determine the optimal concentration of Ascorbic...

13 March 2024 7,500 1 View

¿Cómo puedo saber si una intervención con adolescentes problemáticos ha sido eficaz, o si por el contrario no ha sido adecuada?

Esta pregunta se refiere ha como podemos saber, si después de una intervención, ya sea en grupo o individualmente, a la hora de tratar con adolescentes problemáticos, nuestra intervención a sido...

11 March 2024 7,801 2 View

¿Cuáles son las principales acciones de respuesta del trabajo social, con respecto a menores en riesgo de exclusión social?

Esta pregunta hace referencia a las principales actuaciones, que un trabajador o una trabajadora social, debe de aplicar cuando se encuentra con un menor en riesgo de exclusión social, para que no...

11 March 2024 3,551 2 View

When and where was the term "Univalvia" used for Mollusca?

while attending class my professor asked us to count benthic species,and in my counting i mentioned sea snails,certain i have read multiple times that their classification is "univalvia" since...

27 February 2024 365 5 View

Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you recommend a 96-well plate for minimal cell adherence to the wells during phagocytosis experiments?

I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...

04 August 2024 5,228 4 View

PBMC infection with virus?

In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...

01 August 2024 4,403 4 View

Found this object in the cell culture - do you have any suggestions what it might be?

Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...

01 August 2024 2,250 2 View

Publishing a checklist?

Does anybody know of entomological Journals without page charges that would publish an extensive checklist (Hong Kong Aculeates wasps) covering 350 species (of which more than half are new to Hong...

01 August 2024 6,134 2 View

HEC 1A & HEC1B Cell Lines?

Hi, Kindly guide me that how many cells of HEC1A & HEC1B Cell lines should I seed for Wound healing assay and which plate type is recommended 6, 12 & 24?. Articles suggested mainly 24...

20 July 2024 4,143 2 View

I have two problems: 1) the enzyme is not immobilizing efficiently into the MOF material.. 2) the MOF itself has peak on 400nm by using p-NPA test.?

I am working on carbonic anhydrase immobilization into MOFs. I am facing problems with low enzyme loading.. The other issue is that when using p-NPA activity test to detect the activity of the...

20 July 2024 1,440 3 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View