What degree of missing data in a particular case/participant results in Expectation-Maximisation no longer working?

I'm dealing with a mediation model and am using the PROCESS module in SPSS. Due to SPSS and PROCESS being limited in the imputation methods - being unable to handle multiple imputation - the other...

02 March 2021 4,362 1 View

Has anyone succeeded in capturing uranium atoms in a fullerene structure?

Additional questions are: What are the encapsulating atoms? How difficult was the process and what rates were achieved? What factors most seriously affect the economics?

20 February 2021 3,134 5 View

How to phrase semi-structured interview questions using IPA without biasing superordinate themes?

Hello, I am preparing a semi-structured interview schedule for an interpretative phenomenological analysis study on marginalized individuals' career experiences as impacted by COVID-19. The aim...

19 February 2021 9,099 2 View

No title

19 January 2021 6,848 4 View

Why do my fibroblasts under hypoxia conditions proliferate slower than the same fibroblasts under normoxic conditions?

I am using healthy control lung fibroblasts in a 96 hour experiment with two drugs (nintedanib and Pirfenidone) and vehicle controls for both. I have both hypoxia (approx 1% O2) and normoxia...

12 January 2021 6,260 1 View

How much does radiative heat transfer effect thermal conductivity of materials and how to compare calculations to experirment?

I am calculating the phonon contribution to thermal conductivity for 4 perovskites (BaZrO3, BaSnO3, BaHfO3, and KTaO3) with relatively wide bandgap. When I compare my results for BaZrO3 to the...

27 December 2020 3,232 3 View

Proper method for assessing model invariance following Confirmatory Factor Analysis (CFA) and preceding 2x2 between-subject analysis?

I have produced a good-fitting, reliable baseline model according to CFA. The model contains several factors each loaded by several categorical (ordinal) items. I ultimately intend to analyze the...

15 December 2020 1,668 4 View

How to Reinstall Operating System for a TA Instruments 2910 DSC?

Hard drive crashed on an old windows 2000 that was used to control a TA Instruments 2910 DSC. Installed new hard drive and I am trying to figure out where I can find the software/operating system...

17 November 2020 2,467 3 View

Communities based websites do they serve a purpose?

I'm asking and posing this question as it forms a part of my final project year. I building an ASP.net community-based website coupled with an Oracle database and I'm looking for feedback,...

17 November 2020 7,852 1 View

How can I solve Error: "The coupling service failed to start" during simulation ANSYS 2Way FSI?

Hello, I am dealing with error during lounching 2 Way FSI in ANSYS Workbench. Setup of the Fluent is ok (stand alone I am receiving expected results) and FEM uses Transient Structural. Once I run...

11 November 2020 3,816 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View