Relational Geometry and Polycentric Calculus

01 January 1970 0 143 Report

Hello,

What if there was no distance between 2 origins? I tried to answer this question in this work niversal Measurement Set, S=(0,d,0) d=distance. I won't go into details, you can look at the work.

What do you think?

Preprint Relational Geometry and Polycentric Calculus: A GADU-IOMM Foundation

More Vlasie Catalin Mircea's questions See All

Measuring PSD of a fine powder with Malvern Mastersizer 3000 Aero S, have you ever experienced a "Failed to achieve feed rate demand" error?

Hello! Trying to measure the PSD of a fine powder (0.1-20µm), using Malvern Mastersizer 3000 coupled with Aero S dry dispersion unit, the Feed rate achieved was randomly lower than the Feed rate...

17 December 2023 8,429 0 View

In Robust Control how often is the direct feedthrough term from the disturbance to the measured output non-zero?

Hello everybody, In the context of a generalized uncertain LTI plant G with inputs (d,u) and outputs (v,y): [ A

16 September 2023 118 0 View

Using brms in lie detection research - correct priors in R?

Considering the advantages of bayesian mixed-effects models with informative priors over non-bayesian approaches, I am attempting to figure out the best/most accurate priors to define for my...

16 February 2020 9,525 3 View

How do you minimize/prevent thermal artefact in particle size determination by Malvern Mastersizer 2000 and 3000, using organic dispersants?

There is an important difference between the temperatures of the measuring cell which is located inside the optical system and the dispersion unit which is at room temperature, especially for...

24 March 2019 2,649 13 View

Is it possible that the partial vaporization pressure of SnO2 is so high?

In one experiment we used 4.5 kg of autoclaved pellets and 60% SnO2 content which had been crushed with 8-15 mm granules in a ratio of 0.45 kg k / kg SnO2. The materials were loaded into a...

16 June 2018 7,879 4 View

Supporting vector machine, why if C is large the training error decrease but the test error increase?

Good evening, sorry for the bother. Could someone explain why when i test a SVM for diferent values of the parameter C; as C increases the training error decreases while the test error increases....

08 October 2017 5,391 5 View

Are there any papers that measure how long and emotion lasts after it has been experimentally elicited?

I would like to find a reference demonstrating empirically how long after an elicitation event (e.g., frightening someone), does the elicited emotion last within the individual. I am referring...

14 May 2017 9,845 3 View

How do I interpret a Mediation analysis if PROCESS (Hayes) finds no indirect effect, but using the Causal Steps apporach does find one?

I ran initially a causal steps approach between a variable (A), a predictor (I), and a moderator (G).Using this approach i found that A correlates to I; I correlates to G; A correlates to Gand...

05 September 2016 8,464 3 View

How do I analyse the relationship between a continuous variable and a nominal variable, over several trials?

To give more background, what I have is a personality trait measure (giving a score for each participant) and the answers each participant gave on 20 trials, for which their answers were from a...

12 January 2016 6,124 7 View

Is there a best practice for estimating the construction cost of waste water treatment?

Which is the optimal way to purify waste water compared to the lifetime of the wastewater treatment plant: natural or artificial?

19 July 2014 5,933 3 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

Is it true that there is a physico-statistical meaning to the constant π other than circular geometry but the iron guardians of the SE deny it?

We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...

22 July 2024 4,285 9 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

A new interesting geometry problem. Can you find the measure of angle?

In the isosceles triangle ABC (AC=AB), the angle at the vertex is 20°. Point D is chosen on the side AB such that AD=BC. Find the measure of angle CDB.

23 June 2024 7,541 8 View

The problem at hand concerns the application of the "II Lagrange's formula". Would you like to try solving it?

In triangle ABC, the bisector AL₁ is drawn. Points O₁, O₂, O are the centers of the circles circumscribed around triangles ACL₁, ABL₁, ABC, respectively. The radii are denoted as R₁, R₂, R for...

12 June 2024 7,596 1 View

How to create solid45 elements to an existing cad geometry?

I imported an 3D cad geometry in ansys. Now I want to create the mesh with solid45 element in workbench. How to proceed?

05 June 2024 2,490 1 View

A new interesting problem. Would you like to try solving it?

Consider a circle of radius R with center O. Two other circles are internally tangent to this circle and intersect at points A and B. Find the sum of the radii of the other two circles, given...

29 May 2024 9,788 1 View

Why does my IRC calculation generates higher energy structure around TS ?

While computing the mechanism of a trimethylsilylcyanation related to this work (10.1021/acs.organomet.1c00070) I managed to optimize the geometry of both reactants and product and locate a good...

26 May 2024 9,925 0 View