18 July 2016 1 10K Report

I have been trying but unable to find some redox reactions or electrolytic reactions of pentacene. Help needed please.

Any helpful link, a tip on how to find them or a little list will be appreciated. Thanks in advance.

More Ahmad Mujtaba's questions See All
How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Why tick's salivary gland extract didn't run in the gel (SDS PAGE )??

Greetings, I want to make SDS PAGE for my sample (Tick salivery gland extract), I tried concentrations 10%, 12%. I also tried high molecular weight ladder. But the protein stopped at the top and...

25 February 2021 7,698 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Can the Dunn's test be used as an appropriate post-hoc for the G-test?

Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...

23 February 2021 5,827 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

How to discriminate between Sentinel-2 Level-2A Product Discriminators?

According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...

21 February 2021 5,919 9 View

How to measure the pH of Peat Soil?

Peat possess organic content above 75% and is highly acidic in nature (i.e. pH < 4). Before commencing stabilization, it is mandatory to know about the pH level of peat. Therefore, your...

18 February 2021 9,424 7 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close